Engineering

Air/Water pressure system and controls panels

Bladder air/water pressure cylinders The Bladder air/water cylinders are used to deliver pressurized water up to 1000 kPa to triaxial cells by the pressure distribution panels. The main advantages from using this apparatus are: High degree of accuracy Extremely simple to operate Future expansion of system very easy and relatively low cost Bladder enables the […]

Standalone pressure volume controller, Hydromatic

Multi-positioning, ergonomic and removable 6″ colour Touch screen controller Powers up to two hydraulic pressure lines and measures the associated volume changes Generates water pressure regulated under closed-loop control up to 3500 kPa or 1700 kPa USB pen drive for local data storage Connectable to the GEODATALOG 8 via LAN port allowing data transmission to […]

Double wall triaxial cells for unsaturated tests

Introduction In the traditional triaxial systems, where saturated samples are tested, the volume change measurement is a simple monitoring of the water entering or leaving the sample by a volume change transducer. On the contrary, in the unsaturated systems volume change measurements are complicated by the compressibility of air. If an increase of confining pressure […]

Triaxial cells for advanced applications

Light alloy construction, stainless steel ram and O ring seal Built-in cell ram clamp Includes pillar and anvil for strain dial gauge or transducer Five on/off no-volume changes valves fit as standard For sample sizes between 38 and 150 mm dia. Standard length chambers accepts submersible load cells Rapid assembly design Cells are designed to […]

Standard triaxial cells and accessories

The cell essentially consists of a transparent polycarbonate chamber which has a piston assembly fit to the top and a double flange base fit to the bottom. Three (or six) simple thumbscrew are used to clamp the upper part of the cell to the base, which make assembly and disassembly a very quick and simple […]

Triaxial load frame TRITECH with 4 built-in channels

Ideal solution for advanced and research laboratories that require high productivity and high quality testing; Designed for advanced and research laboratories to perform UU, CU, CD (compression/extension) tests; Very wide variable speed range suitable to perform also unconfined, CBR and Marshall tests.  Double control mode including machine and data acquisition via local touch screen display or from […]

Triaxial load frame TRIAX with 4 built-in channels

Designed for soil testing laboratories to perform UU, CU and CD triaxial tests; Wide 5.7” waterproof touch screen color graphic display allowing machine control, stream on screen data plot and tabulation; Double control mode including machine and data acquisition via local touch screen display or from remote PC (not included) and software (included); USB port […]

Triaxial load frame TRITECH

Ideal solution for advanced and research laboratories that require high productivity levels and high quality tests Designed for soil testing laboratories conducting UU, CU, CD and stress path (compression/extension) tests Due to the variable speed range, unconfined, CBR and Marshall tests can also be performed Suitable for automatic PC-controlled triaxial testing (see AUTOTRIAX 2 system) Allows dynamic […]

Triaxial load frame TRIAX

Ideal solution for commercial laboratories a machine to perform high quality triaxial tests in addition to unconfined and general purpose compression tests. Designed for soil testing laboratories to perform UU, CU and CD triaxial tests on samples from 38 to 70 mm dia. Maximum load frame capacity: 50 kN Maximum testing load depending on the […]

Cyclic simple shear

5 kN horizontal and vertical actuators 5 kN load cells fitted in-line with actuators, 1 N accuracy constant diameter test performance possibility of constant height shear test possibility of constant stress test possibility of constant rate of strain test operating frequency up to 10 Hz (depending on test conditions) The cyclic simple shear apparatus is generally used for research in the dynamic field of soil behaviour, […]

Resonant column

Combined Resonant Column / Torsional Simple Shear device Automatic detection of fundamental frequency RC: damping ratio from half power bandwidth and from free vibration data TSS: damping ratio from hysteresis loops Internal floating frame for large angular and axial deformation Confining pressure up to 1 MPa Suitable for 50 mm dia. specimen (or 38 mm on request) Integrated signal generator and oscilloscope  PC with dedicated software […]

Dynamic pneumatic triaxial systems DYNATRIAX

Capability to perform Static (effective stress and stress path), Dynamic and Unsaturated soil triaxial tests Three axis closed loop control for axial load or displacement, cell and back pressure Automatic compensation of cell/back pressure during dynamic stage Nominal operating frequency up to 10 Hz (depending on the test condition) Complete test automation of all test stages using an high sensitivity closed loop P.I.D. feedback Dynamic load/displacement […]

Dynamic electromechanical triaxial systems DYNATRIAX EmS

Electromechanical Servoactuation, no need of compressed air or hydraulic power supply for the vertical force Capability to perform Static (effective stress and stress path), Dynamic and Unsaturated soil triaxial tests Maximum dynamic load: 15 kN Maximum static load: 10 kN Triple-axes closed loop control of axial load/displacement, cell and back pressure Automatic compensation of cell/back pressure during dynamic stage Operating frequency more […]

Automatic triaxial tests system – AUTOTRIAX 2

24/7 testing without interruption, maximizing productivity and reducing demands on your staff. Automatic execution of up to six independent triaxial tests from start to finish with only one PC; Fully PC control system with multitasking, user-friendlyWindows-based, the PC software complies with relevant standards; High-speed PC closed loop control for continuous monitoring and instantaneous reaction of systems components; […]

Standard triaxial system with external/expandable digital data acquisition

Expandable solution, suitable not only for standard triaxial testing (effective/total stress) but also for other type of soil testing; PC software for remote calibration of the channels and fully comprehensive data acquisition management; Multiple and flexible triaxial configuration (e.g. one frame and three cells)  to perform simultaneously saturation, consolidation and monotonic shear; Data acquisition shared with other soil testing equipment: the […]

Standard triaxial system with built-in digital data acquisition

On-board (via USB) automatic data acquisition for all the sensors required (vertical displacement, axial force, cell pressure, back pressure, pore pressure, volume change);  User friendly 6” touch screen colour panel for local control of load frame and monitoring of the four channels in real time; PC not strictly required for test management: tests can be easily managed from the […]

Standard triaxial system with analogue measurement

Fully analogue data measurement using dial gauge, load ring, double burette and pore pressure transducer; Pore pressure measuring with dedicated readout unit, ensuring a negligible change in volume of the circuit of the pore pressure, as required by the Standards; Pressure system using air/water interface and triaxial panel with air pressure regulators; Easily extended with dedicated accessories to perform […]

Bromhead ring shear apparatus

Microprocessor controlled drive system Speed range adjustable from 0.001 to 180°/min Rapid approach without any limit of rotation Serial port RS 232 for PC remote control Two measurement options: mechanical with load rings and dial gauge, and electronic with Data acquisition, with load cells,  displacement transducer and Geodatalog  Data acquisition system Introduction The Torshear machine […]

Laboratory vane apparatus

Manual or motorized versions available Lightweight, compact and portable, ideal for site or main laboratory Convenient and rapid method of determining shear strength of soft soils Easy to use: many hundreds in operation today The laboratory vane apparatus is based on a original concept of the Transport and Road Research Laboratory of the United Kingdom. […]

Large shear testing machine

Ideal for testing Shale, Industrial slag, Brick rubble, Colliery spoils Sample size up to 300 mm 100 kN shear and consolidation force Steplessly variable speed control from 0 to 11.00000 mm/min Automatic hydraulic application of pre-set consolidationsteps (up to 50) Automatic test management from consolidation to failure: the operator is only requested to remove the clamping screws of the shear box Straight connection between […]

Slotted steel weights

Used for consolidation (oedometers), shear testing machines and other applications. Manufactured from steel. Protected against corrosion. Accurately calibrated assuring the specified tolerance.

Shear box assemblies

These shear box assemblies are designed to be used with our 27-WF2060 Digishear, 27-WF2160 Autoshear and 27-WF2180 Shearmatic shear testing machines. Manufactured from brass and designed to contain the water that surrounds the specimen. They consist of a square box with a rigid walled round or square hole complete with adapter loading pad, retaining plate, […]

Direct and residual shear testing machine DIGISHEAR

Maximum horizontal force: 5 kN Maximum vertical force: 5 kN Infinitely variable speed from 0.00001 to 15.00000 mm/min Digital display LCD 4-row by 20 characters High stiffness load chain shear box – driving head – load cell Compatible with shear boxes up to 100 mm diameter or square Sturdy shear box techno-polymeric carriage untouchable by corrosion Test velocity and travel (forward and reverse) adjustable (residual shear test) […]

Direct and residual shear testing machine AUTOSHEAR

User interface 6″ touch screen colour display for numerical and graphical plotting of the readings Maximum horizontal force: 5 kN Maximum vertical force: 5 kN, using the 10:1 cantilever device Three analogue channels. one for load cell and two for displacement transducers Effective channel resolution: 131,000 points Infinitely variavle speed from 0.00001 to 15.0000 mm/min High stiffness load chain shear box – driving head […]

Automatic shear testing machine SHEARMATIC EmS

Electromechanical servoactuation. Dead weights and air compressor are not required making the test easy and accurate User interface 6” touch screen colour display for numerical and graphical plotting of the readings Maximum vertical force: 10 kN Maximum horizontal force: 10 kN Two displacement transducers measuring vertical settlement and horizontal displacement Two load cells measuring vertical and horizontal force Vertical force load cell […]

Hydraulic consolidation cell for unsatureted samples

Hydraulic loading For saturated and unsaturated specimens Use of the High Air Entry Stone (HAES) Measurement of pore and back pressure during testing Accurate permeability measurements The Hydrocon SWCC consolidation apparatus is used to determine the magnitude and rate of settlement and pressure of unsaturated soil specimens. Because of the low permeability of some materials, […]

Hydraulic consolidation cell

Hydraulic loading Low friction design No weights required Compact design, occupies less space than conventional oedometers Incremental or constant rate of loading tests Suitable for compacted clay Two testing mode available: manual or with automatic data acquisition The Hydrocon hydraulic consolidation cell is the basic part of the apparatus used for the determination of the […]

Constant Rate of Strain cell (CRS)

Continuous monitoring of test parameters (axial load, pore pressure, axial compression) and detailed plotting of the consolidation curve Max working pressure 3500 kPa Relatively short time to perform consolidation test Particularly suitable for cohesive saturated soils Using with standard system with manual control or using dedicated activation code with automatic control and data acquisition. This cell is used to measure the magnitude […]

Oedometers, front loading

Compact and robust design 3 lever arm ratio Screw jack support Same cell for standard and permeability test Possible connection with Data acquisition and processing system This test determines the rate and magnitude of consolidation of a soil specimen restrained laterally and subjected to a number of successive increments of vertical loads. The oedometer consists […]

Automatic Computerized Oedometer ACE EmS

Versatile fully automatic Oedometer soil consolidation testing machine featuring incremental loading, swelling, CRS (constant rate of strain), CHG (controlled hydraulic gradient) and unconfined test. Environmentally friendly and quiet — the ACE EmS benefits from the new Electromechanical Servoactuation (EmS) technology requiring no dead weights or large & noisy air compressors, thus drastically reducing noise levels. Modular and […]

Strenght of stabilized soil

To perform the unconfined compressive strength of hydraulically bound mixtures of fine and medium grained soil specimens, the main Standards require to manufacture the test specimens using a suitable mould set kit. Several versions are available according to the Standard: EN 13286-53 NF P94-100 Each test set conforming to EN 13286-53 includes: 1 mould, set of 2 end […]

Pinhole test apparatus

Certain fine-grained soils with high sodium content are highly erodible by the water flowing through them. During the test the flow of water under a high hydraulic gradient through a cavity in the soil is reproduced. The test apparatus consists of a cylindrical metal container fit one end with water inlet and the other end […]

Combined constant or falling head apparatus

Used for both constant or falling head methods for determining the soil permeability. The apparatus consists of a two section plastic chamber, a plated steel top with gaskets, a plastic funnel reservoir 550 mm max. head with reservoir upright, a 100 cc pipette, and two porous stones 63.5 mm dia. x 12.7 mm thick, 300 […]

Compaction permeameters

This apparatus is used to control the water supply in the constant or falling head permeability tests on compacted soils. The permeameters comprise valve, water inlet or outlet, mould and collar, filter baseplate. The stand consists of an aluminium panel complete with Perspex tubes and graduated rules for falling head permeability tests and water tank […]

Constant Head permeability apparatus

The soil permeability is a very important factor to study the behavior of soil in its natural condition with respect to water flow. The constant head method is particularly suitable for relatively coarse grained soil such as sands and gravel. For fine grained soils such as clay-like or silty soils see Falling head permeability apparatus. The […]

Light Weight deflectometer

Fast and cost-saving: maximum 2 minutes per measuring point No vehicle required Immediate on-site evaluation of test results It can be easily operated and carried by one person only Testing can be achieved in difficult to reach locations The dynamic plate load test performed with the Lightweight deflectometer is used to determine the soil bearing […]

300 mm dia. Platen test set, Swiss method

Used to estimate the bearing capacity of a soil under field loading conditions on flexible pavement components . The relatively lightweight (68 kg in total) and small dimensions of the apparatus make it very easy to use and to move from one place to another. The measuring bridge made from aluminium alloy, is very light […]

Bearing plate test apparatus – DIN

4 different configurations with 100 and 200 kN capacity, analogue and electronic versions Analogue versions fitted with 200 mm dia. triple scale manometer:  force (kN), oil pressure (Bar) and specific load (MN/m2) Electronic versions fitted with high resolution load cell Dual flow hand pump for quick contact to the reaction frame and for accurate test […]

Bearing plate test apparatus

Multiple testing configurations complying with international Standard and fulfilling any customer’s need 3 capacities: 100, 200 and 500 kN Analogue, digital or electronic readings matching all budgets Analogue version with 200 mm dia. triple scale manometer:  force (kN), oil pressure (Bar) and specific load (MN/m2) Digital version with digital read out unit featuring wide graphic […]

Vibration compaction hammer

Constant speed with variable speed control Durable aluminium housing Soft grip and shock-absorbing handle Easy to change tool by single-step holder Variable lock mechanism to adjust tool at 12-step angle Functional and robust design Used for the compaction of Proctor and CBR soil specimens. Using the appropriate tamping foot it can also be used for […]

Impact soil tester

Results can be directly correlated to the CBR test An essential trench control tool for all cable and pipe laying service contractors Used to obtain an indication of the degree of compaction of soil in road construction. Results can be directly correlated to the CBR test. The unique microprocessor system automatically checks all readings throughout […]

NF Balloon density apparatus

For the determination of the in-situ density of well bonded soil according to NF specifications. A metal cylinder is filled with water which is then pumped into a rubber membrane, mounted on the base of the cylinder, which take up the hole previously made in the soil pavement. The water pressure is controlled by a […]

Balloon density apparatus

Used to determine the in-situ density of compacted or firmly bonded soils. The test set consists of a graduated cylinder 1596 ml capacity, housed inside an aluminium guard, a reversible rubber aspirator pump, a density plate 9” square and 12 rubber balloons. Weight approx.: 6 kg accessories 35-T0131/4   Rubber balloons. Pack of 12.

BS Sand replacement test sets

The verification of the degree of compaction can be determinate on site by a simple procedure consisting essentially in removing and weighing a part of compacted soil and replacing in the hole with sand by a simple apparatus recording the volume of sand and then calculating the density of the removed soil. We propose three […]

Sand replacement test sets

The verification of the degree of compaction can be determinate on site by a simple procedure consisting essentially in removing and weighing a part of compacted soil and replacing in the hole with sand by a simple apparatus recording the volume of sand and then calculating the density of the removed soil. We propose three […]

Relative density of cohesionless soil test sets

This method, in the EN standard, covers the determination of the maximum dry density and water  content of cohesionless materials when compacted using a vibrating table. Materials for which yhis method is applicable may contain up to 12% by mass fines (<0.063 mm). The maximum particle size of the materials to be tested is 80 […]

Gay-Lussac specific gravity bottles

The determination of the specific gravity and density of fine soils is developed through three different operations: the sample, introduced in the specific gravity bottle, has to be thermostatically normalized by immersion in a suitable water bath complete with Adjustable tray and Cover with cooling coil (see accessories), then de-aired using a dessicator connected to […]

Magnetic stirrers

Used for titration and stirring. Variable speed. Magnetic Teflon coated follower included. 81-B0145/D version feature a hot plate wich can be useful for particular applications. Models 24-D0448 24-D0448/B 81-B0145/D Rotation speed, rpm 100 to 1200 100 to 1200 100 to 1200 Power, W – – 700 Dimensions, mm 120x120x45 180x180x70 170x230x150 Max temperature, °C – […]

pH papers

Used for determining the pH of aqueous solutions.

pH meters

We propose different models, suitable for field and laboratory use, as follows: – Poket digital PH meter, battery operated – Portable pH, mV, temp. digital meter, complete with stand for laboratory use. Battery operated   24-D1847 Pocket digital pH meter, battery operated. pH range: 0.00 to 14.00, Resolution: pH 0.01, Accuracy at 20°C: +/- 0.2 […]

Water test kits

Acidity Test Kit The Acidity Test Kit is equipped with all you need to determine acidity of water. The kit is quick, easy to use and portable. This makes it practical for field as well as laboratory use. The design makes the kit easy to handle and, except for HI 3820-0, practically prevents accidental injury […]

Sulphate content

Two model are available: Rapid method (BS 812:117 | ASTM C88 | AASTHO T104 | EN 1367-2) Sulphate test strip, detection range 200 to 1600 mg/l. Useful for preliminary assessment of sulphate ions in aqueous solutions. Weight approx.: 10 g Laboratory method – Ion exchange apparatus (BS 1377:3) Used for determining the sulphate content of ground […]

Quantab chloride titrators

This method provides a measurement of water soluble chloride salts present in a soil or aggregate sample. It is based on the Volhard method. Weight approx.: 10 g

Moisture condition apparatus

Used in the assessment of earthworks for construction by comparison of compaction characteristics at various moisture contents, to determine  “Moisture condition value” and “Chalk crushing value”. This robust apparatus is designed for use in the construction laboratory and incorporates a rammer, scale, counter and mould. Weight approx.: 55 kg Accessories 33-T0064/1 Moisture condition mould. 33-T0064/2  […]

Dessicator cabinet

Used to store and maintain dry the soil sample previously dried in oven to avoid the absorption of the air humidity until the complete cooling. Made from transparent plastic for a clear view of content. The unit include an internal metal frame with adjustable shelves. The cabinet has to be normally completed with a suitable […]

Moisture determination balance

Simultaneous drying and weighing of sample Automatically and simultaneously dries and weighs solid samples for the determination of moisture content. Provides a continuous direct readout for both weight and percentage moisture loss through the entire cycle. Built in timer. Capacity/Resolution: 160g x  0.001 g Timer: 0-99 min with 1 minute interval Dimensions: 194x340x235 mm Weight […]

Universal moisture tester

The universal moisture tester can be used for soils, sand and fine aggregates. The 19-T0019, -T0019/G and -T0019/H models can determine moisture contents of 2% or under on samples up to 100g in mass, the 19-T0019/F long bottle version can determine up to 20% on 20g samples, while the Speedy models are suitable for determinations […]

Speedy moisture testers

A well established portable test method for the determination of moisture content of soils, sand and fine aggregates. The procedure involves the reaction between water and calcium carbide which when mixed together give off a gas. The amount of gas is directly proportional to the amount of water present in the sample and results in […]

CBR equipment, EN version

This method is used for the laboratory evaluation of subgrade and subbase coarse materials in road construction. To perform this type of test, we propose moulds with various accessories listed in the table below and manual compaction rammers. Different models are available conforming to the various relevant specifications. Please note that very frequently, some of the […]

CBR equipment, NF version

This method is used for the laboratory evaluation of subgrade and subbase coarse materials in road construction. To perform this type of test, we propose moulds with various accessories listed in the table below and manual compaction rammers. Different models are available conforming to the various relevant specifications. Please note that very frequently, some of the […]

CBR equipment, BS version

This method is used for the laboratory evaluation of subgrade and subbase coarse materials in road construction. To perform this type of test, we propose moulds with various accessories listed in the table below and manual compaction rammers. Different models are available conforming to the various relevant specifications. Please note that very frequently, some of the […]

CBR equipment, ASTM/AASHTO version

This method is used for the laboratory evaluation of subgrade and subbase coarse materials in road construction. To perform this type of test, we propose moulds with various accessories listed in the table below and manual compaction rammers. Different models are available conforming to the various relevant specifications. Please note that very frequently, some of the […]

Universal load frames accessories for soil, asphalt, concrete, cement, mortar and rock testings.

50 and 100 kN load frames (motorized or hand operated) are suitable for a wide range of tests on different kind of materials. Each test requires a list of accessories depending on the type of test and on the reference standard. View odering information to select the list of accessories suitable for each universal frame […]

MULTISPEED digital automatic universal tester for displacement controlled tests

The firmware provide the digital speed control and a number of important test functions as follows: Closed loop speed control CBR and MARSHALL test speed can be selected by default. Other testing speeds (Custom) between 0.2 and 51 mm/min, can be easily set. Selection of maximum platen displacement.  The automatic stop of the machine avoids machine and specimen overloading, thus assuring operator safety. Rapid approach function, to reduce […]

MULTISPEED automatic universal tester with touch screen digital speed control and data acquisition

Stand-alone automatic digital load frame Closed-loop speed control Four channel on board data acquisition CBR and MARSHALL test speed can be selected by default Speed calibration function by firmware. Integrated transducer calibration facility Infinitely variable speed from 0.05 to 51 mm/min can be easily set by keyboard Selection of maximum platen displacement with automatic stop […]

50 and 100 kN bench machines for CBR, Marshall, multipurpose compression and flexure testing on asphalt, soil, rocks, mortar, groundcement and cement

CONTROLS range includes a series of small and compact compression machines that can be used for several tests: CBR tests on soils; Marshall tests on asphalt; uniaxial and unconfined tests on soils and rocks; compression tests on low stregth concrete, cement and groundcement samples; flexure tests on beams, mortar, tiles and any other compression or flexure test performed under displacement […]

CBR motorized loading press

Max. load: 50 kN Test speed: 1.27 mm/min Load measurement: by load ring, fitted with 0.001 mm high resolution dial gauge to fulfill the standard requirements Complete with adjustable penetration piston and dial gauge 30 mm travel x 0.01 mm division The machine feature a rigid two column frame with upper crossbeam, which can be […]

Hand operated CBR loading press

The machine feature a rigid two column frame with upper crossbeam, which can be adjusted in height and locked in position with locknuts. The drive force is provided by a mechanical jack housed in the base cabinet. The machine include a precision load ring, 50 kN cap., penetration piston and dial gauge. The CBR test […]

Field CBR test set and conversion frame for laboratory use

CBR test can be performed not only in laboratory but also in-situ. CONTROLS proposes a dual purpose test assembly that, connected to the suitable accessories, can satisfy both needs: for field testing, 34-T0115/A includes all necessary components that, along with vehicle bracket code 34-T0115/9, can be used for in-situ determination of bearing capacity of soils used in road construction. […]

Proctor/CBR automatic compactor to ASTM/AASHTO

Automatic programmable compactor to Standards ASTM and AASHTO Graphic display showing test progress in real time Possibility to program up to 3 user defined compaction cycles and sequences  Rammer with both head and weights included Unique rammer lifting device to guarantee correct and longlife drop height All safety features as protection guards and emergency button included as […]

Universal Proctor/CBR automatic compactors

Universal automatic application: one single model that fulfills all Standards requirements  (ASTM/AASHTO/EN/NF/BS/UNE etc.), including the central blow User friendly selection of Standards EN, ASTM/AASHTO, BS, NF and other major International Standards by software Possibility to program up to 15 user defined compaction cycles and sequence  Rammers and rammers kit for easy interchangeability according to all International standards included All safety features as protection guards […]

Proctor moulds and rammers, BS

Used for determining the relationship between the moisture content and density of compacted soil. The mould includes collar, mould body and base plate. The rammer construction includes a guide sleeve with vent holes. Different versions are available that conform to the various commonly used standards. They are all made of plated steel and are identical […]

Proctor moulds and rammers, NLT/UNE

Used for determining the relationship between the moisture content and density of compacted soil. The mould includes collar, mould body and base plate. The rammer construction includes a guide sleeve with vent holes. Different versions are available that conform to the various commonly used standards. They are all made of plated steel and are identical […]

Proctor moulds and rammers, NF

Used for determining the relationship between the moisture content and density of compacted soil. The mould includes collar, mould body and base plate. The rammer construction includes a guide sleeve with vent holes. Different versions are available that conform to the various commonly used standards. They are all made of plated steel and are identical […]

Proctor moulds and rammers, EN

Used for determining the relationship between the moisture content and density of compacted soil. The mould includes collar, mould body and base plate. Steel plates may be used at the end of compaction on top of last layer (optional). The rammer construction includes a guide sleeve with vent holes. Different versions are available that conform to […]

Proctor moulds and rammers, ASTM/AASHTO

Used for determining the relationship between the moisture content and density of compacted soil. The mould includes collar, mould body and base plate. The rammer construction includes a guide sleeve with vent holes. Different versions are available that conform to the various commonly used standards. They are all made of plated steel and are identical […]

Laboratory digital planetary mixer

New mixing speed control system, granting a much wider range of speed: it is possible to set the right mixing speed to avoid the formation of dust while mixing. Whisk/Planetary speeds adjustable from 12/5 to 149/65 rpm, depending on the mix consistency. Continuously variable speed (VFD technology). Completely new interface with digital alphanumeric display 2×16 characters with […]

Melting pot

Used to melt wax toi seal the soil samples and other materials. The temperature is set and maintained at the desired value. Adjustable thermostat and pilot lamp fully isolated conforming to CE requirement. Complete with cover. Capacity: 5 l approx. Temperature range: +30 to +150°C Power: 700 W Internal dimensions: 200 mm dia.x160 mm high […]

Soil Cutter

Ideal for breaking up lumps of clay to prepare soil specimens for compaction. Entirely made of 304 stainless steel. Horizontal shaft and revolving bowl with high cutting speeds (two speeds for bowl and knives), to make very thin grindings   – Power: 2300 W – Capacity: 15 liters – Dimensions: 830x590x610mm ( w x d x […]

Universal specimen extruder

Used to remove 4” (101.6 mm), 6” (152.4 mm), 100 mm, 150 mm diameter specimens from Proctor, CBR and Marshall moulds. Steel structure with adapters that can be easily fit conforming to the mould diameter. Capacity: 50 kN Maximum ram stroke: 197 mm (ram) + 68 mm (screw) Weight approx.: 25 kg

Mortar and rubber pestle

Used to gently crush individual particles for chemical tests. Total weight approx.: 1 kg

Soil extruder, motor operated

Features one of the largest capacities available on the market (ram stroke 900 mm), and due to the large number of standard adaptors, is considered the most versatile extruder. The machine exerts a max. thrust of 60 kN and is very simple to operate: a lever controls the extruding speed  and the hydraulic valve for […]

Soil extruder,hand operated

This hydraulic extruder can accommodate standard U4 tubes and a range of adaptors to extrude soil samples 35, 38, 101.6, 106 and 152.4mm dia. It can also be used to remove Marshall, Proctor and CBR specimens. Appropriate accessories and adaptors are available and have to be ordered separately. See accessories. Max load cap.: 60 kN […]

Soil sampler, cutter and extruder

Specimen cutting: up to 100mm circular and square samples – Speciment extrusion: up to 200mm high samples (more than 600mm daylight is required for 100mm dia sample extrusion) – Upper plate size: 120mm – Vertical Daylight: 620mm – Overall sizes: 525x360x1530mm ( included the rack and pinion mechanism extended) – Weight: 22kg   This versatile sampler can be […]

Soil lathe, trimmer, extruder

Specimen lathe function: from dia. 35×70 mm to dia.100×200 mm Specimen trimming and extruding function: from dia. 35×70 mm to dia. 50×100 mm This apparatus is used to prepare any size of cylindrical soil sample: – Specimen lathe function: from dia. 35×70 mm to dia. 110×220 mm – Specimen trimming and extruding function: from dia. 35×70 mm to dia. 50×100 mm- The apparatus which can be used either as a trimmer or as a sampler consists […]

Plastic limit set

Used for determining the lowest moisture content of a soil at which the sample can be rolled into little rolls, 3 mm dia., without breakages. The set includes: 22-T0040/1 Plastic limit plate, 300×300 mm 22-T0040/2 Stainless steel rod 3 mm dia. 86-D1171 Mixing dish 120 mm dia. 86-D1630 Flexible spatula 86-D1329/A Moisture content tin dia. […]

Shrinkage limit set

Used for determining the maximum moisture content at which the soil does not shrink after drying the sample. The set includes: 22-T0035/1 Shrinkage dish 45 mm dia. x 12.7 mm high. (Q.ty 2) 22-T0035/2 Crystallizing dish, 57 mm dia. x 31 mm deep 22-T0035/3 Shrinkage prong plate. Manufactured from transparent acrylic and fit with 3 metal […]

Liquid limit devices (Casagrande)

Used to determine the moisture content at which clay soils pass from a plastic to a liquid state. Comprises: removable brass cup, adjustable crank and cam mechanism, blow counter, and base. Different  versions are available conforming to the various Standards in use. They are identical in shape and differ, generally, from the type of base […]

Liquid limit penetrometers

Cast iron base with leveling feet Digital penetration measurement gauge 0.01 mm precision Micrometer vertical adjustment device Automatic zeroing Electronic release mechanism (22-T0029/E model only)  The cone penetrometer apparatus is used to determine the moisture content at which clay soils pass from a plastic to a liquid state and it is used also for the […]

End-over-hand Shaker

Used for determining the particle density of soils by the Gas Jar method. This method applies for soils containing up to 10% of particles retained on a 37.5 mm sieve. Consisting essentially of a motor speed reducer which rotates two clamps which holds the Gas jars 22-D1132 (see accessories). -Weight approx.: 20 kg Accessories 22-D1132 Gas […]

Particle size analysis set: NF method

Used for determining the particle size distribution of very fine materials such as silt and clay. The set include the following items: 22-D1007/A Hydrometer jar, 2500 ml cap., graduated at 500, 1500 and 2000 ml. 2 pieces 22-T0062/A Soil hydrometer from 0.995 to 1.030 g/ml. 22-D1007/A1 Hand stirrer 82-D1199 Glass thermometer 0 to 50°C, div. 0.5°C […]

Particle size analysis set: Pipette method

Used for determining the particle size distribution of very fine soils. Basic items to perform the test are the 22-T0062/1 Andreasen pipette which is hold by the 22-T0062/2 Pipette stand for raising or lowering precisely the pipette to the required level without disturbing the suspension under test. The 22-T0062/3 sedimentation cylinder is submerged in the […]

Particle size analysis set: hydrometer method

Used for determining the particle size distribution of very fine materials such as silt and clay. The set include the following items: 22-D1006/A Hydrometer jar. 6 pieces. 22-T0060/31 Rubber bung for 22-D1006/A 22-T0060/A  Soil hydrometer 151 H, from 0.995 to 1.038 g/ml. As alternative, model 22-T0060/B, 152 H, from -5 to 60 g/l, also available. See accessories. […]

Water level indicators

Used for determining the water level in boreholes, wells and other open underground structures. Drum mounted, with an ON/OFF indicator and audio signal when probe touches water. The sensing portion of the probe has a stainless steel tip with plastic shielding to prevent false readings. Probe diameter of 10 mm allows an easy passage through […]

Field inspection testing kit

Ideal for geotechnicians, geologists and agronomists. It consists of the 16-T0163 Pocket penetrometer and of the 16-T0174 Field inspection pocket vane tester. 16-T0163 Heavy duty model, all stainless steel construction, three interchangeable tips: 4.5 mm dia. for very hard soil, 6.35 mm for medium and soft soil, 8.98 mm for soft soil. Supplied complete with […]

Shear hand vane tester

Two models available: 16-T0174 for field surface and deeper measures. Especially designed to measure the undrained shear strength (CU) of cohesive soils, consists of a cylindrical body with a torsional spring and three interchangeable vanes of different sizes used depending upon the expected strength of the soil. The height/diameter ratio of all vanes is 2. […]

Dial penetrometers

Three versions  available: 16-T0160 and 16-T0162 respectivety for soft soil and medium/hard soil; 16-T0161 complete with 5 different plungers used to evaluate the angle of internal friction “j” of sandy soil and the cohesion “c” in clay soils.  They all include a peak hold feature with 0 setting by push button. Models Scale [kgf/cm2] Plunger […]

Pocket penetrometers

Designed for making field classification of cohesive soils in terms of consistency, shear strength and approximate unconfined compressive strength. Two models available: 16-T0163 Heavy duty model, 16-T0171 standard model,   16-T0163 Stainless steel construction. Tip Diameters: 4.5 mm dia. for very hard soil, 6.35 mm for medium and soft soil, 8.98 mm for soft soil. […]

Proctor penetrometer

Used for establishing the moisture content-penetration resistance relationship of fine-grained soils. It consists of a special spring dynamometer with pressure indicating scale on the stem of the handle. A sliding ring on the stem indicate the maximum pressure obtained in the test. Supplied in a wooden carrying case. Load scale: 0 to 55 kg , […]

TRL Dynamic cone penetrometer

This apparatus, originally developed by the TRL-UK Transport Research Laboratory, has been designed  under licence from TRL for the rapid in-situ measurement of the structural properties of existing road pavements constructed with unbound materials. Continuous measurements can be made down to a depth of approximately 850 mm or, when extension shafts are used, to a […]

DCP – Dynamic cone penetrometer

This apparatus in used for the rapid in-situ measurement of the structural properties of existing road pavements constructed with unbound materials. Continuous measurements can be made down to a depth of approximately 850 mm or, when extension shafts and rods are used (available as accessories), to a recommended maximum depth of 2 m. Where pavements […]

Lightweight dynamic penetrometer

Penetrometers are used to establish the thickness of different stratifications when investigating the suitability of a site for bridge, road or other construction works. In general if the ground is not too compact, penetration tests with this apparatus can be carried out to depths of about 8 to 12 m. The apparatus includes: Anvil with […]

Piston volumeter

An easy to use pocket device very useful  to determine the in-situ density of undisturbed soil. A stainless steel tube is driven into the soil and the volume is read on the stem marked from 0 to 30 cm3. Weight approx.: 0.5 kg

Core cutters

The core cutter is driven into the soil using the driving hammer. Then the core is dug out, trimmed, weighed, dried and the density and moisture content calculated. Made of steel protected against corrosion. The set includes core cutter, driving dolly and driving rammer. Two versions available: dia. 100x 130 mm high and dia. 150×180 […]

Surface soil sampler, ASTM

Used to take a standard volume sample from the ground in order to establish the in-situ density of the soil. The apparatus consists of a 5 kg sliding weight drop hammer, which falls freely onto the driving head situated on top of the sampling tube ID 73×66 mm high. Made from steel protected against corrosion. […]

Soil colour charts

The Munsell Soil Color Charts are an affordable way to evaluate the type of soil that is present within a given area. The book is set up to make soil color evaluations in the field quickly and easily. The soil classification system that has been developed around Munsell Color System is an established and accepted […]

Soil prospecting kit

It comprises all the most popular auger and sampler housed in a practical carrying case. It consists of: 16-T0005/A  Hand auger head 80 mm dia. 16-T0006/A  Hand auger  head 100 mm dia. 16-T0007/A  Hand auger head 150 mm dia. 16-T0008/A  Spiral soil auger head 40 mm dia. 16-T0008/B  Dutch soil auger head, Edelman model, 70 […]

Sampling equipment

Used to take undisturbed soil sample in soft and fine soils. The apparatus comprises TY-handle, Extension rod, Jarring link, Stainless steel sample tube 38×230 mm length. The sample is obtained by percussion, lifting all the upper assembly which slides inside the jarring link and forces the sample tube into the soil. Weight approx.: 7 kg […]

Auger power head

Used in conjunction with sampling tube to obtain disturbed or indisturbed samples of soils. Two models available. Augers and extension rods for 16-T0009/M 16-T0009/M1   Auger dia. 100×1000 mm 16-T0009/M2   Auger dia. 150×1000 mm 16-T0009/M3   Auger dia. 200×1000 mm 16-T0009/MEX  Extension rod 1000 mm long Note: Augers 100 to 200 mm dia. for 16-T0009/L and 250 […]

Augers

Used for general exploration in soil investigation. Made of special plated steel. The T handle with 1 m rod has to be ordered separately. See accessories, code 16-T0005/1. A complete set of augers and accessories is also available. See Soil prospecting kit. Weights approx.: 16-T0005/A  2 kg 16-T0006/A  2.5 kg 16-T0007/A  3 kg 16-T0008/A  3 kg 16-T0008/B  2 kg 16-T0008/C  1.3 kg […]

Flexural test devices for mortar beams

Robust frame fitted with an upper bearer that moves vertically supported by springs. One of the two lower bearer can tilt horizontally and the distance between the two bearers is 100 mm for the EN version 65-L0019/B and 119 mm for the ASTM version 65-L0019/C. Apart from that, the two models are identical. Total height […]

Compression-flexure cement testing frames

Four columns robust frame with single or double test chamber. Simple effect ram with electrical limit switch. Single test chamber model 65-L17Z10 incorporate compression bearing plates with spherical seat for portion of prisms 40x40x160 mm broken in flexure conforming to EN 196-1. All the other models, single or double test chambers, are fitted with 165 […]

AUTOMAX, Super-Automatic compression-flexural cement testers

Fully automatic test cycle. The complete test cycle is automatically performed by simply pressing the start button (both via display and via software). Correct test execution according to selected Standards, is continuously and automatically controlled. See additional information. PC control option. Double user interface based on display and PC. When connected to PC, the system is […]

PILOT Automatic compression-flexural cement testers

Automatic test cycle. Correct test execution according to selected Standards, is continuously and automatically controlled. See additional information. Dual user interface display and PC Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale. Special calibration starting from 3kN for 300kN chamber and from 0.5kN for 15kN available on request. See upgrading […]

Compression-flexure cement testing frames, multipurpose models

High rigidity: solid one piece steel frame Universal compression testers, in practice, suitable to house various accessories for testing cement, mortar, resins and other materials Special calibration starting from few kilonewtons available on request (see upgrading options) when connected to suitable control unit large testing space Best quality/price ratio  These Multipurpose compression / flexural testers have […]

500-600 and 500-600/15 kN cement compression and flexural machines, multipurpose models. PILOT Control System

Automatic closed-loop test cycle according to selected Standards. Dual user interface display and PC Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale Special calibration starting from few kN available on request; Compatible with the new, intuitive and smart DATA MANAGER Software Adopt the latest ES Energy Saving technologies for reduction of power consumption and silent operation Double stage hydraulic pump […]

500-600 and 600/15 kN cement compression and flexural machines, multipurpose models. WIZARD 2 Control System

Multipurpose machine ideal for Central laboratories, for testing Cement, Mortars, Resins, Refractory, Lightweight concrete, Soil-cement specimens etc; digital control system with wide high-contrast display 4×20 characters and 6 keys membrane keyboard; real time display of load and stress and applied load rate by symbols for easy adjustment; accuracy Class 1 (EN) and Class A (ASTM) starting from 10% […]

Automatic flexure/tension machine

Constant rate of loading Dual range Automatic stop at failure Accepts flexural or briquette specimens Single lever loading assures high accuracy This machine is used for the flexural strength determination of cement specimens 40.1x40x160 mm and tensile tests on cement briquettes. It consists of a beam loading system with a travelling weight driven by an […]

Circulating water bath with cooler unit

Automatically maintains the set temperature Two channels electronic thermoregulator: heating/cooling with digital display Complete with recirculating unit Incorporating refrigeration compressor Ideal for conditioning Asphalt specimens for Marshall and Indirect tensile tests Ideal for cement specimens cure in water A multi-purpose unit usable for many other applications This multi-purpose digital unit, fit with cooler unit and […]

Cement curing bench-type cabinet

Specifically made for curing cement, mortar, lime and gypsum specimens Large stainless steel bench, 2240 x 700 mm, which can be conveniently used as working table Internal curing temperature adjustable from 18 to 30°C Temperature accuracy ±1°C Internal humidity range 95 ± 5 % RH Also suitable for water curing using a suitable can  Ideal […]

Curacem, Cement curing cabinet

Strong polypropylene structure chemical resistant Internal  robust stainless steel racks High capacity Humidity from 95% to saturation by water nebulizers Connectable to water refrigerator for better temperature control Ideal for curing cement specimens in commercial and site laboratories, very practical and easy to use. The frame is made of strong polypropylene structure, which is chemical […]

Vibrating machine for 70.7 mm cube moulds

For the preparation and compaction of 70.7 mm mortar cube specimens. The mould table is mounted on four springs attached to an eccentric shaft which allows each sample to be vibrated at 12000 cycles per minute in accordance with the specifications. The cube mould is not included and has to be ordered separately. See accessories. […]

50 mm three gang cube mould

The 50 mm cube specimens are produced for compression test. The dimension is compatible with ASTM C109. Made from steel, precisely machined. Weight approx.: 6 kg

Jolting apparatus

Easy verification of compliance to standards: weight distribution, dimensions etc. Rigid structure assuring stability and no distortion High resolution graphical display 128×80 pixels and 6 keys membrane keyboard Double test procedure: it is possible to set the target revolutions / drops or the total working time Rapid mould lock and release system Noise reduction cabinet […]

Three gang moulds 40x40x160 mm

Individually checked with certified instruments All parts marked and identified Model 65-L0010/B has a minimum surface hardness of HV 400 and is surface protected with a rust inhibitor treatment. Supplied complete with traceable certificate of conformity. Both models can be fit with 65-L0010/5 pegs for determining the coefficient of thermal expansion conforming to EN 1770 Used […]

Fully Automatic Mortar mixers, AUTOMIX

Automatic testing cycles Automatic sand dispenser and additional dispenser for manual addition of admixtures or water during the mixing cycle 4 programmable mixing cycles conforming to EN and DIN standards 10 mixing cycle programmable by the operator Acoustic signal synchronized with cycle steps Ergonomic and safe design  This mixer has been developed with a high […]

Automatic programmable mortar mixers

Complete with stainless steel mixing bowl, EN beater and open-type sand hopper Machine operated by a dedicated and easy to use in-built software Digital mixer, user friendly interface with functional alphanumeric display 2×16 characters and keybord The pre-defined procedures guide the operator in mixing operations according to Standards allowing manual introduction of sand by the top […]

Digital mortar mixers

Complete with bowl and beater conforming to EN Standards                            Continuously variable speed (VFD technology) Either Standard or user defined speeds can be easily selected (also adjustable during mixing) Blade/Planetary speeds adjustable from 30/13 to 380/165 rpm, depending on the mix consistency 3-points bowl […]

Fluidity test of grouts for pre-stressing tendons: grout spread method

Mould for grout spread test consiting of a stiff plastic mould, 39 mm internal diameter, 60 mm high, weight 60 g approx. Accessories 22-T0040/1 Glass plate, 300 x 300 mm.

Steam cabinet for building lime soundness

For use with Le Chatelier moulds for the determination of the soundness of building lime which is subjected to the continuous action of steam at atmospheric pressure for a period of 180±10 min. Stainless steel internal chamber housed in a stainless steel insulated exterior case. Power: 700 W Internal dimensions (lxdxh): 280x250x150 mm Outside dimensions: 480x400x210 mm […]

Kleine apparatus

Used for the determination of the carbon dioxide in lime. Consisting essentially of a decomposition flask 50 ml cap., of an absorption vessel to contain the potassium hydroxide solution, a measuring burette, funnel stopcocks, connections and wooden stand. To perform the test, a hot plate with magnetic stirre and an adjustable height support are alo […]

Water permeability determination of one-coat rendering mortars with substrates

The apparatus consists of a metal cone 200 mm dia. base with a reference mark at 100 mm and a glass burette 1 litre capacity with 1 ml graduation. The burette is held by appropriate base with rod and clamps.

Flow test apparatus for grouts

Used for determining the consistency of the expansion pre-mixed cement mortars. Consisting of a special funnel fited on a metal channel. Overall dimensions (lxdxh): 954x205x370 mm Weight approx.: 6,5 kg

Wet sieving apparatus

The apparatus, used for determining the fly ash fineness by wet sieving, comprises  a special stainless steel sieve, 0.045 mm opening, a spray nozzle 17.5 mm dia. with 17 holes 0.5 mm dia oriented ans spaced conforming to the specifications, a pressure gauge 80 mm dia. and fittings for connection to the water supply. Weight […]

Mud balance

The mud balance provides a simple method for the accurate determination of mud density. The durable construction make it ideal for field use. Principally the balance consists of a base and graduated arm with cup, lid, knife-edge, rider, built-in spirit level, and counter-weight. The constant volume cup is affixed to one end of the graduate […]

Marsh funnel viscometer

Marsh funnel is used for routine viscosity determinations on almost every drilling rig. Made of rugged, break-resistant plastic that resist to the temperature change deformation. Volumetric accuracy is assured. Plastic handle provides insulation for user’s hand. A metal orifice assures accurate readings. Supplied complete with plastic measuring cup 1 liter capacity.

Flow cone apparatus

Used for determining the flow properties of mortars, grouts, muds and many other type of fluid materials. The apparatus comprises a metal stand supporting the stainless steel cone having inside dimensions of 150 mm inside upper dia. x 280 mm height. When fit with the 10 mm nozzle the total height is 350 mm. The […]

Slaking vessel

Used to determine the yield of lime by leaving the sample to slake in an insulated vessel. Comprising a stainless steel cylinder, 113 mm dia. x 120 mm  deep, externally isolated, complete with cover. Overall dimensions: 155 mm dia. x 200 mm height Weight approx.: 2,1 kg

Bulk density apparatus

Used for determining the bulk density of lime by the fall of the sample from a standard height into a container. Consisting of a cylindrical container I liter cap., hopper and spring loaded yoke.

Reactivity test apparatus

Two versions available: with standard digital thermometer and with datalog thermometer complete with temperature probe Ground quicklime shall be tested for their reactivity with this apparatus which consists essentially of a Dewar vessel, 1000 ml cap., stirring motor, calibrated thermometer, stand and accessories. Two versions are available: 64-L0035/E: supplied with digital thermometer 64-L0035/D: with advanced datalog thermometer, temperature […]

Air content meters

These apparatus have been designed to determine the bair content in cement  mortar, cement paste, and lime mortar. The testers are made of cast aluminium. The test pot and the upper part are sealed air-tight together by means of two quick-action spring clamps. The air ia compressed by means of a built-in hand pump. This […]

Plunger penetration apparatus

Used for determining the consistency of masonry cement and building limes. Consisting of a steel base with recess to house the test cup and the vertical column holding the penetration plunger assembly. The height of drop is 100 mm and the weight of plunger assembly is 90 g. Supplied complete with test cup 80 mm […]

Water vapour permeability test cell

Used to determine the water vapour permeability of hardened rendering and plastering mortars. Made of hard plastic resistant to corrosion. Permeability area of 0.02 m2 approx. Weight approx.: 1 kg

Flow tables for mortar and building lime

High resolution graphical display 128×80 pixels and 6 keys membrane keyboard  8 languages can be set: Italian, English, French, Spanish, Polish, Portuguese, Romanian and Cesky  Double test procedure: it is possible to set the target revolutions / drops or the total working time Used to determine the consistency of mortars and building lime. Two versions […]

Automatic Vicat apparatus

New functional and ergonomic design based on the innovative CVi-TECH philosophy invented by CONTROLS througt the recent years Advanced electronics technologies providing superior performances and total flexibility combined with simplicity in use Easy-to-use double interface: local mode, with large size 4,3″ touch screen color display, and remote mode, with PC Supplied complete with PC software […]

Gillmore apparatus

Use to determine the setting time of cement. The apparatus consists of two horizontal arms which carry two weighted steel needles precisely machined to meet5 the requirement. The initial needle 2.12 mm dia., weighs 113 g and the final needle 1.06 mm dia., weighs 453,6 g. Weight approx.: 2.5 kg

Standard Vicat apparatus

The Vicat frame consists essentially of a metal stand with a sliding rod. An adjustable indicator moves over a graduated scale. The needle or plunger is attached to the bottom end of the rod to make up the test weight of 300 g. The frame 63-L0028/1 is supplied without accessories, which have to be ordered […]

Muffle furnace, 1200

Used for determining the loss on ignition of cement and building lime. Max. temperature: 1200°C Power: 4200 W Inside dimensions (lxwxh): 210x280x145 mm Overall dimensions: 510x650x650 mm Weight approx.: 70 kg

Calorimeters

Resolution 0.001°C System accuracy up to 0.05°C Instrument memory for up to 10,000 readings Displays, saves and prints Delta T, min, max and mean value Audible alarm if limit values are exceeded Protection class IP65 PT100 probe measuring range -40 to +300°C Complete with resolution test certificate Supplied complete with MS EXCEL template for data […]

Water retention apparatus

Used for determining the water retention value of cement and lime. Two models available: – one fitted with aspirator pump and analog vaccum gauge with regulator – the other with a portable vacuum pump and digital vaccum gauge with regulator

Carbon dioxide content in cement

The testing equipment consists of: Y-piece with Mohr clip; CO2 absorption tower for gas or air stream; dropping funnel; distil­lation flask with electric mantel heater and three-armed still head; condenser; wash bottle for concentrated sulphuric acid; two absorption U-tubes for Hydrogen Sulphide and water respectively; three absorption tubes for water and carbon dioxide. Two of […]

Bulk density of cement

Used to determine the bulk density of cement as specified by the “Commission des méthodes d’essai des matériaux de construction”. It consists of a sieve funnel, an unit weight measure 1 litre capacity, a tripod, and straightedge. Overall dimensions: 350x350x520 mm Weight approx.: 3 kg

Blaine fineness apparatus

Used to determine the particle size of Portland cement, limes and similar powders expressed in terms of their specific surface.  It consists of a stainless steel cell, perforated disc and plunger. An U-tube glass manometer is fit to the steel stand. The set is supplied complete with rubber aspirator, pack of filter paper and thermometer. […]

Prism mould 75x75x285 mm to UNI

Used for expansion test on concrete prisms to UNI 11604. Accessories 62-L0035/A Length comparator,  digital gauge 12.5×0.001 mm, with output for PC connection (special cable required) 82-D1261/LINK Serial cable for PC connection 62-L0034/1 Reference INVAR rod 295mm long. Spare parts 62-L0033/U1 Spare contact points for 62-L0033/U and 62-L0033/UU moulds. Pack of 30.

Prism mould 25x25x280 mm to UNI

Used for accelerated expansion test on mortar prisms to UNI 11504.   Accessories 62-L0035/A Length comparator,  digital gauge 12.5×0.001 mm, with output for PC connection (special cable required) 82-D1261/LINK Serial cable for PC connection 62-L0034/11 Reference rod 294mm long Spare parts 62-L0009/A1 Spare contact points for 62-L0033/B moulds. Pack of 10.

Two gang prism mould 25x25x285 mm to ASTM

This mould is the same used for the Expansion of Portland cement with the High pressure autoclave, conforming to ASTM C151 and ASTM C490. 62-L0035/A Length comparator,  digital gauge 12.5×0.001 mm, with output for PC connection (special cable required) 82-D1261/LINK Serial cable for PC connection 62-L0034/1 Reference INVAR rod 295mm long to ASTM C490 Spare […]

Mortar bar container for accelerated method

Used for determining the potential alkali reactivity of cement aggragate combination (mortar bar method) up to 80° (accelerated method). Stainless steel cylinder container and internal stainless steel rack to hold specimens.

Mortar bar container

Used for  determining the potential alkali reactivity of cement aggragate combination (mortar bar method). Acrilic cylinder container and internal stainless steel rack to hold specimens. Two models available according to the Reference Standards.

Autoclave, high pressure

The autoclave consists of a high-pressure steam vessel with internal dimensions 154 mm dia. x 430 mm high to accept a rack for holding 10 specimens obtained with the 62-L0033/B moulds (see accessories). Complete with pressure gauge, pressure regulator, temperature regulator, control switches, safety valve and specimen rack. Certified conforming to ISPELS procedure.   Heater: […]

Hydraulic shrinkage mould 25x25x285 mm

This mould is the same used for the Expansion of Portland cement with the High pressure autoclave, conforming to ASTM C151 and ASTM C490. 62-L0035/A Length comparator,  digital gauge 12.5×0.001 mm, with output for PC connection (special cable required) 82-D1261/LINK Serial cable for PC connection 62-L0034/1 Reference INVAR rod 295mm long to ASTM C490 Spare […]

Hydraulic shrinkage mould 40x40x160 mm

The 62-L0009/F version is used for the determination of linear shrinkage of cement mortars (EN 12617-4). The same mould can be used for testing grouts conforming to EN 12808-4 replacing the standard plugs with the 62-L0010/H2 and placing two 15x40x160 mm plastic inserts  62-L0010/H3 inside each compartment. See accessories. Three gang mould, individually tested with […]

Length comparator

Including digital gauge 12.5×0.001 mm with serial output for PC connection This apparatus is used for a number of length measurements concerning mainly cement and mortar specimens with different lengths. For this reason the reference rods are not included and have to be ordered separately, consulting for an easy and quick choice, the specification table. […]

Le Chatelier moulds

Introduction Used for determining the expansion of cement. The mould consists of a spring tensioned split cylinder 30 mm internal diameter, 30 mm high with two indicator stems which measure 165 mm from the points of thje centre line of the cylinder and O ring. Two or three moulds are required for each test. To […]

Le Chatelier flask

Used to determine the specific gravity of hydraulic cement and lime. Glass flask 250 ml capacity, with graduated neck from 0 to 1 ml and from 18 to 24 ml in 0.1 ml graduation with accuracy of 0.05 ml. Weight approx.: 500 g Accessories  62-D1635  Chattaway spatula

Cement samplers

62-L0001, Packaged cement tube sampler Used to sample cement from packages. Made of brass, it has an outside dia. of 32 mm x 700 mm long. – Weight approx. 2 kg 62-L0002, Bulk cement sampler Used to sample cement in bulk storage or bulk shipments. It consists of two brass concentric tubes with slots. The […]

Joint roughness coefficient test device

It is used to calculate the JRC of a rock or joint. The device consists of an adjustable inclined plane, on which the rock sample (100 mm max dia.) is placed, separated along the surface where the roughness is to be measured. Then the plane is slowly tilted until sliding of the upper part of […]

Rock classification hammer

Used to measure the rebound index on rock cores and samples. The device is simple, easy to use, and is similar to the one used for testing concrete. The level of impact energy only is different: 0.735 Nm. Rock cores are positioned horizontally and the rebound index is obtained from the average of several measurements […]

Profilometers (Barton comb)

Used for measurement of the roughness profile of rock samples.

Rock piks and hardness scale

Used for preliminary rock identification. 45-D1710 Fully polished, leather grip. Weight approx.: 650 g 45-D1711 Fully polished, nylon vinyl grip. Weight approx.: 550 g

Digital rock strength index apparatus 100 kN cap

100 kN capacity Superior functionality and usability of the equipment, since the pump is separate from the frame Ergonomic digital read out unit with wide graphical display and 6 keys membrane keyboard Effective resolution: 18 bit (1/262’000 div.) Load measurement accuracy: ± 1 % Load resolution: 1 N Supplied complete with traceable calibration certificate for […]

Slake durability apparatus

Maximum 4 drums can be used simultaneously to improve testing productivity Complete with display showing the residual testing time (10 minutes as per ASTM indications) Transparent water tanks with level mark to help correct water filling Compact machine for saving space in the laboratory Drums with quick-release drive units for rapid mounting / disassembling This […]

Abrasion testing machine

Transparent protection cover Control flow abrasive outlet according to the Standard Supplied complete with sample calibration made in Boulonnaise marble, 115x115x50 mm Digital counter unit This machine has been developed for determining the resistance to abrasion/wear of natural stones and concrete products. Easy to use, electronic control of the disc speed with auto shut-off of […]

Böhme abrasion wheel tester

Easy setting of test speed and number of cycles; fast sequence selection option; counter and test status always displayed; simple use; compact design; memory option; emergency shut off button included. The disc abrader conforming to Böhme method consists of a rotating wheel made of cast iron, 750 mm dia., with a defined test track to […]

Rock permeability equipment

This apparatus, originally designed for soil mechanics test applications, can also be used to provide an infinitely variable constant pressure and is used in conjunction with the Hoek cell fit with the permeability end caps, for the investigation of the permeability of rock at high confining pressure, in the laboratory. The apparatus comprises: motorized hydraulic […]

Rock shear box apparatus

Shear box made in aluminium alloy Maximun axial and shear load capacity: 50 kN Reversable shear action with 48 mm stroke Double version available: analogic and electronic Data processing template available as accessory for the digital version 2 mould formers included in the testing configuration    This apparatus was originally developed at Imperial college, London, […]

Compression test device for rock specimens

Strictly compliant to ASTM D7012 Rock core specimens Test Methods The Rock core shall have a diameter from 54.7 mm (NX type) to 63.5 mm (HQ type) Heavy duty / high stiffness compression device Max. load capacity: 1200 kN High stiffness structure and the high performance steel making this device particularly suitable for high strength […]

Compression/Splitting test device

We propose two compression device models for indirect tensile test (splitting test) conforming to ASTM D3967 and to ISRM Specifications. Model conforming to ASTM D3967 This apparatus, originally developed for testing in compression cement specimens, can also be used for splitting tensile test on rock disks with dimensions from dia 54 mm to 64 mm. […]

Strain gauges for Uniaxial and Triaxial tests

They provide a very accurate electrical signal, strictly proportional to the strain of the specimen submitted to load application, for determining the Elastic Modulus and strength characteristics as alternative to the Compressometer-Extensometers 55-C0222/F. They can be applied to the specimen surface by a special Adhesive-Catalyst agent and other accessories all included in the 82-P0399/C Strain […]

Hoek cells and sample extruder

Various Hoek cells dimensions are available: AX, 1.5″, BX, NX and HQ types Designed for high pressure capability All models are fitted with two quick-release self-sealing coupling One rubber sleeve is already included with the Hoek cell The Hoek triaxial cells are offered in five models of different size; each one consists of the following: […]

Semi-automatic Uniaxial and Triaxial test system. Basic test apparatus

Suitable for determining elastic modulus and strength characteristics of rock specimens under uniaxial and triaxial conditions Composed by 2 indipendent systems: high stiffness compression machine and low friction manual pressure maintainer Max working lateral pressure: 70 MPa Advanced external data acquisition system with new touch screen Datalog 8 The Semi-Automatic configuration for determining the elastic modulus […]

Automatic Uniaxial and Triaxial test system

Automatic performance of uniaxial and triaxial tests with individual but combined control of axial load and confining pressure Axial and horizontal stress are increased isotropically up to a defined level in automatic way The 2 consoles are operated independently and the failure envelope is obtained by few individual tests (single – stage) with automatic application […]

Stress path triaxial and uniaxial automatic test system

Advanced testing system suitable for extremely variable materials, from soft sandstone to high-strength marbles Determination of Elastic modulus, Poisson’s ratio and strength characteristics of rock specimens under uniaxial and triaxial conditions Automatic performance of triaxial tests with combined control of axial load and confining pressure Multiple failure stages triaxial test (stress – path mode) carried […]

Automatic system for uniaxial and triaxial tests on rock cores including stress path and permeability determination

Advanced testing system suitable for extremely variable materials, from soft sandstone to high-strength marbles Determination of Elastic modulus, Poisson’s ratio and strength characteristics of rock specimens under uniaxial and triaxial conditions including permeability measurement Automatic performance of triaxial tests with combined control of axial load and confining pressure Multiple failure stages triaxial test (stress – […]

Rock sample verification apparatus

Used to verify the dimensional and shape tolerances of rock core specimens up to 75 mm dia. by 120 mm length.  The straightness of the cylindrical surface can be easily verified as well as flatness and verticality of end surfaces by the same dial gauge using the magnetic holder in the desired position. The apparatus […]

Rock specimen grinding machine

To grind concrete specimens, natural stones, tiles, block pavers, ceramic materials etc. Large base table for grinding contemporaneously up to three 100 mm cubes, or three 150 mm cubes, or two 200 mm cubes and concrete/tile blocks of various sizes (see drawing of working area). For cubes up to 200 mm and cylinders up to […]

Core trimmer and cut-off machine

Specifically designed for rock testing laboratories To obtain samples from irregular rock or core pieces Double function of trimmer and cut-off apparatus Complete with safety device conforming to CE requirements Used to obtain rock samples perfectly machined (cube, prisms, etc) from irregular rock or core pieces. It is supplied complete with a proper vice to […]

Rock, concrete and masonry saw

Trolley and water tank are zinc plated to avoid corrosion Head adjustable in height and the tilting motor head permits cuts up to 45° inclination Cooling water pump and filter included  This universal saw, completed with the suitable accessory, can be used to cut concrete / rock cores and irregular rock samples in order to […]

Laboratory coring machine and bits

This machine is specifically used in the laboratory for cutting core samples from hard materials such as rock and concrete. A clamp is provided to firmly secure the material during the cutting cycle. The coring area is protected by a transparent cylinder. A special clamping device to prepare rock samples from core pieces is also […]

Setting tendency of bitumen emulsions

Used for determining settling tendency of bitumen emulsions. 600 ml capacity, with one division mark at 500 ml. Complete with two closeable side tubes. Weight approx.: 1 kg Note: To perform the test the 81-B0155/B Water in bitumen emulsions test set  is also required.

Breaking value of cationic emulsions test set

The breaking value ia a dimensionless number corresponding to the amount of reference filler, in grams, needed to coagulate 100 g of bitumen emulsions. The test is performed with a set of items comprising: Feeding pan Two enamel dishes Nickel spatula Support base and clamp. The above set correspond to the basic “Equipment for manual […]

Storage stability tester

The test is based on settlement measurement conforming to NF T66-022. It consists of a 12 V current source, vessel, cylindrical electrode and holder. Overall dimensions: 200x200x520 mm Weight approx.: 4 kg

Glass tube with fused-on glass filter

Used for determining the penetration power of bitumen emulsions. 41.5 mm internal dia., 115 mm approx. total height, fit with glass filter disc pore size between 160 and 250 µm. Weight approx-: 1 kg

Test sieves for mixing stability

Used for determining the mixing stability of emulsions with cement.

Test sieves for residue on sieving

Used for determining the residue on sieving of bituminous emulsions.

Emulsified asphalt distillation apparatus

Used to examine the asphalt emulsions composed principally of a semi-solid or liquid asphaltic base, water and an emulsified agent. The apparatus consists of an aluminium-alloy still with ring burner, a glass connecting tube with water-cooled condenser, a graduated cylinder 100 ml cap, support stands, holders and two thermometers range -2 to 300°C. Weight approx.: […]

Particle charge tester

This equipment is used for the identification of anionic and cationic bituminous emulsions used in road construction. For this purpose, it has two electrodes that are introduced into the emulsion, connected to a continuous power supply, in which after a time of passing a current through the emulsion, it can be observed which of them […]

Test set for the determination of solubility

The set is proposed in two versions: ASTM D2042 , code 81-B0148 including: 86-D1044 Filter flask 500 ml cap. 86-D1189 Funnel for Gooch crucible 86-D1188/B Gooch crucible 86-D1188/1 Rubber ring for Gooch crucible 86-D1188/B1 Filter discs, fiberglass, 37 mm dia. Pack of 100 86-D1189/1 Rubber stopper EN 12592, code 81-B0148/A including: 86-D1044 Filter flask 500 […]

Water in bitumen test set

Used for determining the water content of bituminous and petroleum materials by distillation with a water immiscible, volatile solvent. Comprising: Glass still 10 ml Glass receiver Glass condenser Electric heater with thermoregulator Power: 250 W Weight approx.: 4 kg  Spares 81-B0155/1   Glass receiver 10 ml 81-B0155/2   Distillation flask 500 ml 81-B0155/3   Glass condenser

Hubbard-Carmick bottles

Used for determining the breaking point of solid and semi-solid bitumens. The Fraas Breaking Point is the temperature at which bitumen first becomes brittle, as indicated by the appearance of cracks when a thin-film of the bitumen on a metal plaque is cooled and flexed in accordance with specified conditions. The apparatus consists of a […]

Breaking point apparatus

Used for determining the breaking point of solid and semi-solid bitumens. The Fraas Breaking Point is the temperature at which bitumen first becomes brittle, as indicated by the appearance of cracks when a thin-film of the bitumen on a metal plaque is cooled and flexed in accordance with specified conditions. The apparatus consists of a […]

Apparatus for distillation of cut-back asphalt

This apparatus is used for the examination of cut-back asphaltic materials by the distillation test. It consists of: Distillation flask Condenser Adapter Shield Shield and flask support Electric heater with thermoregulator Cylinder receiver Thermometer -2 +400°C Weight approx.: 6 kg  81-B0150/E   Apparatus for distillation of cut-back asphalt. 230 V, 50-60 Hz, 1 ph 81-B0150/EZ   Apparatus […]

Pensky-Martens Digital Tester

This instrument covers the determination of the flash point of petroleum products in the temperature range from 40 to 360°C. The tester covers both “procedure A” (applicable to distillate fuels, lubricating oils) and “procedure B” (residual fuel oils, cutback residual, mixtures of petroleum liquids with solids) of ASTM D93. The instrument is heated by an […]

Tag open cup flash point tester

Used for determining the flash point of volatile flammable materials. Conforming to CE requirements. Consisting of: Electric furnace with electronic controller of heating power Flame rotating ignition device (LPG supply is required) Glass cup Insulating plate Support and clamp for thermometer Gauge Stainless steel frame Double line fuse Thermometers not included. See accessories. Power: 600W […]

Cleveland flash tester

Conforming with CE directive Protection grid included for safety Used for determining the flash and fire point of petroleum products. It consists of a brass cup mounted on an electric heater with temperature controller. Conforming with the CE European directive, is supplied complete with double line-fuse, hot plate control system and thermometer -6 +400°C. Power: […]

Air bath

Used for softening bituminous materials before tests. The stainless steel vessel can receive up to 600 g of bitumen. Built in thermoregulator. Heat protection. Power: 600 W Dimensions: 170x230x300 mm Weight approx.: 3 kg

Bacon sampler

Used to obtain bitumen or oil samples from various levels. Made from brass. Dimensions: 80 mm dia. x 250 mm long Weight approx.: 1.5 kg

Saybolt viscometers

This method covers procedure for the empirical measurement of Saybolt viscosity of petroleum products at specified temperatures between 21 and 99°C. The viscometers, available in two versions: single and two tubes, include bath, Furol and Universal orifice, key, control box, stirring device, cooling coil, 60 ml flask and digital thermoregulator. Funnel and withdrawal tube ars […]

Engler viscometer

Thermometers 82-B0121/1  Thermometer ASTM 23C, range +18 +28°C, subdiv. 0.2°C 82-B0121/2  Thermometer ASTM 24C, range +39 +54°C, subdiv. 0.2°C 82-B0121/3  Thermometer ASTM 25C, range +95 +105°C, subdiv. 0.2°C 82-B0121/4  Thermometer IP 76C, range +10 +55°C, subdiv. 0.5°C, immersion 93 mm Flask and strainer 81-B0120/2   Kohlraush calibration flask 200 ml cap. 81-B0120/4   Strainer No. 50 ASTM […]

Standard Tar viscometer

Used for determining the viscosity of cut-back bitumen and road oil. The apparatus, housed in a stainless steel case, consists of a tank fit with a thermostat, a rheostat, an agitator, an immersion heater to take the water to the required temperature and cooling coil for connection to the water supply. The temperature is checked […]

Dynamic viscometers

Cannon-Manning  and Asphalt institure vacuum viscometers Used for determining the viscosity of bitumen at 60°C. Supplied complete with calibration certificate. For determining the dynamic viscosity all the above viscometers have to be introduced in the 81-B0116/A Viscometer bath by the appropriate Holder: 81-B0117/H1 for Cannon-Manning models and 81-B0117/H2 for Asphalt institute models. Pressure regulator and […]

Kinematic viscometers

Cannon-Fenske opaque viscometers Used for the determination of kinematic viscosity of liquid asphalts (bitumens) and road oils at 60°C and distillation residue of liquid asphalts and asphalt cements at 135°C. Cannon-Fenske Opaque models are suitable for opaque liquids. Supplied complete with calibration certificate. Zeitfuchs cross-arm viscometers Used for the determination of kinematic viscosity of liquid […]

High Performance Rotational Viscometer

• Selected speed r.p.m. • Selected spindle SP • Viscosity reading cP (mPa·s) or cSt • Percentage of full scale % • Sample temperature °C or F • Shear Rate (with coaxial spindles) SR (s -1) • Shear Stress (with coaxial spindles) SS (N/m2) • Density (introduced by the user) g/cm3 • Viscosity reading: dynamic […]

Standard Rotational Viscometer

Data displayed: selected speed, selected spindle, viscosity reading, percentuage of full scale Relative and absolute viscosity Unit converter SI to CGS AUTO_TEST with sound and visual mulfunction alarm AUTO-RANGE function User-enabled calibration 10 languages options Repeteability: 0.2% Accuracy 0,1% of full scale   Apparent viscosity of unfilled asphalt is evaluated by a rotational viscometer  which […]

Bending Beam Rheometer BBR

Durable, corrosion-resistant construction Computerized control, data acquisition and analysis PID temperature controller with digital display Two independent platinum RTDs for precise temperature control Mechanically-refrigerated cooling bath with environmentally-safe non-CFC coolant Integral LVDT and temperature compensated load cell for accurate test results Includes complete calibration kit with carrying case Includes ASTM/AASHTO-compliant specimen moulds PC and software […]

Vacuum Degassing Oven VDO

Platinum RTD temperature internal measurement to +/- 0.1° C Selectable test temperature (from ambient to 200° C) controlled to +/- 4.0°C Integrated vacuum pump Vacuum monitored by transducer and controlled to 15 +/-0.1 kPa absolute pressure Digital touch screen 6″ display for temperature, vacuum, set points and actual values Reclining display allowing view from any […]

Pressure Ageing Vessel PAV

Platinum RTD temperature internal measurement to +/- 0.1° C Freely selectable test temperatures from 80° to 120°C, PID controlled to +/- 0.5°C   Efficient heating system allowing the test temperature to be achieved in one hour, exceeding the Standards’ specification Programmable pre-heating functions (limited to 60° C to avoid accidental burns during sample rack positioning) […]

Rolling thin film ovens (RTFOT)

Touch-screen display with 4.5” color control panel, including timer function, visual warnings and digital air flow regulator Full conformity to temperature specifications (time to reach target temperature after switch on, target temperature adjustment after samples insertion) from the Standards Carousel rotation with closed-loop controlled speed Safety features: Automatic over-temperature switch, door switch, pilot lamp and […]

TFOT bitumen oven

Used for determining the loss in mass (exclusive of water) of oil and bituminous and the effect of heat and air on a film of semi-solid bituminous material. Depending on the standard in use, the TFOT oven has to be completed with the accessory to perform the test as follows: For EN 13303, ASTM D6, […]

Research Ductilometer for Force Ductility test on standard and modified bitumen – DUCTIMETER

4 tension line (briquette capacity) x 1500 mm Easy and free access to the large testing space Double drive screw rod Closed-loop PID temperature control system Stainless steel insulated water bath Exclusive in-built thermoregulation system compensating the control, optimized by the connection to chiller (optional) High carriage return speed of 500 mm/min for greater productivity […]

High Performance Ductilometer for Force Ductility test – Ductimeter

4 tension line (briquette capacity) x 1500 mm Easy and free access to the large testing space Double drive screw rod Closed-loop PID temperature control system Stainless steel insulated water bath Exclusive in-built thermoregulation system compensating the control, optimized by the connection to chiller (optional) High carriage return speed 500 mm/min for greater productivity Adjustable […]

Standard Ductilometer for Ductility test – Ductimeter

4 tension line (briquette capacity) x 1500 mm  Easy and free access to the large testing space Closed-loop PID temperature control system Stainless steel insulated water bath  Exclusive in-built thermoregulation system compensating the exchange of heat and cooling, resulting in a very strict temperature control, optimized by the connection to chiller (optional) Adjustable speed range […]

Automatic ring and ball apparatus

Microprocessor control Automatic programmable test sequences for water or glycerol RS 232 serial port for PC or printer Large graphic display 240×128 pixel Memory up to 50 tests Language selection This advanced microprocessor controlled automatic tester is used to determine the softening point of bitumen using water or glycerol as heating fluid. The softening point […]

Standard ring and ball apparatus

Used for determining the softening point of bituminous materials. Comprising: 81-PV0145/1 Brass rings (2 pieces included in set) 81-PV0145/2 Steel balls 9.5 mm dia. (2 pieces included in set) 81-PV0145/3 Ball centering guide (2 pieces included in set) 81-PV0143/1 Glass vessel 81-PV0145/5 Pouring plate 81-PV0145/6 Ring holder/assembly 82-D1200/1 Glass thermometer, -2 +80°C, 0.2°C graduation, ASTM […]

Penetrometer, Fully Automatic model – PIVOT

Fully automatic operation. The entire test cycle (rapid approach, starting point determination, penetration and return to the initial position) is automatically performed by simply pressing the start button on the touch screen display Rapid approach and automatic starting point determination to eliminate any operator inaccuracy during needle position Penetration measurement via contactless displacement transducer, with […]

Standard penetrometers

Digital penetration measurement Complete with micrometer vertical adjustment Semi-automatic version with automatic controller, complete with micrometer vertical adjustment and adjustable electronic timer of the fall time Digital circulation water bath with cooling coil and immersion probe available. An additional water chiller is available but not strictly necessary The electronic timer allows the user to set […]

Bearing plate and Benkelman beam apparatus

To determine the bearing capacity and deflection of subgrade and subbase of roads. The apparatus comprises: 80-B0180/B1  Aluminium bearing plate 600 mm dia., with reinforcing ribs. Weight approx.: 30 kg 80-B0180/B2  Hydraulic jack, 200 kN cap. Weight approx.: 10 kg 80-B0180/B3  Set of three interchangeable extensions with spherical seated foot. Weight approx.: 12 kg 80-B0180/B4  Hand pump with precision […]

Permeameter for draining pavements. Autostrade method

For measuring the water percolation time through the draining pavements. Transparent cylinder, 150 mm dia., 390 mm high. Weight approx.: 6 kg

Permeameter for draining pavements

For measuring the water percolation time through the draining pavements. The apparatus comprises a graduated transparent cylinder, a metal support, a rubber gasket and a 20 kg counterweight with handles. Weight approx.: 21 kg

Radial flow falling head permeameter

Consisting of an acrylic tube 125 mm internal diameter, marked from 1 to 5 l cap., with internal rubber ball and rod. The permeameter is fit on a wooden base plate with sealing gasket. Weight approx.: 8 kg

Van Asbeck Apparatus for flexibility test on hydraulic bituminous mixes

The scope of Van Asbeck apparatus is to test and assess the flexibility property and related impermeability to water under pressure of hydraulic bituminous mixes to be used to cover the water storage of dams. The apparatus consists essentially of a steel cylindrical cell divided in two sections: the upper part that is the under […]

Specific gravity frame and baskets

Used with a suitable electronic balance for specific gravity determination of fresh and hardened concrete and aggregates. A purpose built robust frame designed to support the electronic balance. The lower part of the frame incorporates a moving platform, which carries the water container allowing the test specimens to be weighted in both air and water. […]

Benkelman beam apparatus

The apparatus is used to measure the deflection of flexible pavements under the axion of moving wheel loads. In operation the beam is placed between the tyres of the test vehicle and in contact with the pavement. The deflection is measured as the vehicle passes over the test area. The probe is 2440 mm long […]

Sand absorption cone and tamper for consistency

Cone and tamper manufactured according to specifications. This item is also used for determining the specific gravity and absorption of fine aggregates. See Sand absorption cone and Pyknometer. Weight approx.: 250 g

Cohesion tester

For determining the proper consistency (mix design) for a slurry seal mixture. Pneumatically operated, it consists of a double acting, double end-rod pneumatic cylinder fit in a frame, which houses the pressure gauge and valves. A hand torque tester is also supplied. The tester has to be completed with the suitable Square mould. See accessories. […]

Planetary stirrer for abrasion test

For determining the resistance to abrasion of slurry mixtures. The apparatus consists of a planetary mechanical stirrer equipped with a weighted rubber hose abrasion head. The machine has to be completed with the set of moulds. See accessories. Weight approx.: 32 kg Accessories 80-B0192/1   Set of moulds 295 mm dia., 6.3, 10.0, 13.0, 19.0 mm […]

Travelling beam for detecting surface irregularities

The apparatus is used for detecting the road surface irregularity. It can be used either for concrete or asphalt pavements. The apparatus consists essentially of a beam with rigid wheels at the extremities and a wheel at the middle, which can detect any vertical deviation of the surface from a straight-line between the two wheels […]

Sand patch apparatus

This test is performed spreading a measured volume of glass spheres (ASTM and EN) or fine sand (NF) into a circular patch on the road surface and filling the surface depressions to the level of the peaks. The apparatus comprises the following parts: Measuring brass cylinder Spreader disc with surface covered by rubber Glass sand or […]

Rate of spread apparatus

This simple equipment is for determining the rate of spread of binder on the surface of the road. The equipment consists of a metal 300 mm square tray, which can be lifted by means of four chains. The chains are attached to a balance and the rate of spread can be assessed by a digital […]

MOT Straightedge

Used to measure irregularities in road pavement. Made from aluminium alloy, 3 m length. Complete with two steel wedges. Wooden carrying case is not included and must be ordered separately. See accessories. Weight approx.: 10 kg 80-B0185/B1 Wooden carrying case for MOT Straightedge and related wedges

Skid resistance and friction tester

New low friction release mechanism of the pendulum arm for beter accuracy Extremely light pointer, for high precision results. Slider lifting system integrated in the pendulum foot that guarantees reliable adjustment operations Stiff and stout twin column structure Easy and reliable height adjusting system Integrated additional scale for tests on PSV specimens Complete with  calibration […]

Vialit adhesion test apparatus

Used to assess the adhesion property of aggregates to bitumen. The method is a check on the adhesion of aggregates to be applied to the surface of wearing course rolled asphalt. The apparatus consists of a metal basement with three vertical pointed rods to hold the test plate; vertical rod 50 cm high with a […]

Duriez compression test sets

The test is performed to determine and study the physical and mechanical properties of bituminous mixtures. Two mould sizes: 80 and 120 mm dia. All parts are made from steel protected against corrosion. The specimens have to be temperature conditioned with a suitable climatic chamber (see Climatic chambers, model 10-D1429/A)and the compression test has to be […]

Los Angeles abrasion machine

High stiffness welded steel frame High resolution graphical display 128×80 pixels and 6 keys membrane keyboard  8 languages can be set: Italian, English, French, Spanish, Polish, Portuguese, Romanian and Cesky  Double test procedure: it is possible to set the target revolutions / drops or the total working time The machine can be mounted inside a […]

Indentation penetrometer

New weight positioning system, allowing in a very user-friendly and precise method to pass from unload to preload phase, then to load phase without the need to add/remove weights from the structure. Four-columns frame structure, with high stiffness. Piston position indicator, making easier the adaptation of the penetrometer to different height samples. Stainless steel water […]

Vibrating hammer for P.R.D. specimens

Constant speed with variable speed control Durable aluminium housing Soft grip and shock-absorbing handle Easy to change tool by single-step holder Variable lock mechanism to adjust tool at 12-step angle Functional and robust design Used for the compaction of Proctor,  CBR soil specimens (see Vibration compaction hammer) and P.R.D. Percentage refusal density  test, using the 33-T0087/7 […]

Automatic impact (Marshall) compactor, EN

Automatic control Complete protection for operator safety to CE prescriptions High resolution graphical display 128×80 pixels and 6 keys membrane keyboard Improved rammer lifting device, constant height fall, modern and reliable design User friendly rammer replacement system Noise reduction and security cabinet available on request. The apparatus automatically compacts the sample and stops after the […]

Automatic Marshall compactors, ASTM

Both versions feature automatic control and a reliable rammer lifting device High resolution graphical display 128×80 pixels and 6 keys membrane keyboard Noise reduction cabinet available CE versions complete with safety guards for operator protection and emergency stop button CE versions 76-B4442, 76-B4443, 76-B4444 The apparatus automatically compacts the sample and stops after a preset […]

Marshall hand compaction assembly

The assembly consists of a wooden compaction pedestal,  support rod to hold the hammer in perpendicular position,  compaction hammer and mould holder. All parts can be ordered individually. See spare parts. For automatic compaction see Automatic Marshall compactors, ASTM. Total weight approx.: 50 kg Spare parts 76-B0058/A   Compaction hammer 76-B0059   Compaction pedestal 76-B0059/1  Hammer guide 76-B0056/A   […]

Marshall compaction moulds

All moulds are made from steel, protected against corrosion. They are specially made for use with the automatic compactor, see Automatic Marshall compactors, ASTM. The three parts of the compaction moulds can be purchased individually. See spare parts. Conforming to ASTM D6926 (ex D1559), the compaction can also be performed manually. See Hand compaction assembly. Model […]

Circulating water bath with cooler unit

Automatically maintains the set temperature Two channels electronic thermoregulator: heating/cooling with digital display Complete with recirculating unit Incorporating refrigeration compressor Ideal for conditioning Asphalt specimens for Marshall and Indirect tensile tests Ideal for cement specimens cure in water A multi-purpose unit usable for many other applications This multi-purpose digital unit, fit with cooler unit and […]

Water baths

Ideal for conditioning asphalt specimens for Marshall and Indirect Tensile tests; water conditioning up to 60° (up to 95°C with our larger model); wide internal area to accomodate several specimens; supplied with perforated base shelf and internal case; +/-1°C accuracy; 0.1°C resolution.  Used to condition Marshall (60±1°C) and other asphalt specimens (e.g. tar specimens at […]

Universal load frames accessories for soil, asphalt, concrete, cement, mortar and rock testings.

50 and 100 kN load frames (motorized or hand operated) are suitable for a wide range of tests on different kind of materials. Each test requires a list of accessories depending on the type of test and on the reference standard. View odering information to select the list of accessories suitable for each universal frame […]

MULTISPEED automatic universal tester with touch screen digital speed control and data acquisition

Stand-alone automatic digital load frame Closed-loop speed control Four channel on board data acquisition CBR and MARSHALL test speed can be selected by default Speed calibration function by firmware. Integrated transducer calibration facility Infinitely variable speed from 0.05 to 51 mm/min can be easily set by keyboard Selection of maximum platen displacement with automatic stop […]

MULTISPEED digital automatic universal tester for displacement controlled tests

The firmware provide the digital speed control and a number of important test functions as follows: Closed loop speed control CBR and MARSHALL test speed can be selected by default. Other testing speeds (Custom) between 0.2 and 51 mm/min, can be easily set. Selection of maximum platen displacement.  The automatic stop of the machine avoids machine and specimen overloading, thus assuring operator safety. Rapid approach function, to reduce […]

50 and 100 kN bench machines for CBR, Marshall, multipurpose compression and flexure testing on asphalt, soil, rocks, mortar, groundcement and cement

CONTROLS range includes a series of small and compact compression machines that can be used for several tests: CBR tests on soils; Marshall tests on asphalt; uniaxial and unconfined tests on soils and rocks; compression tests on low stregth concrete, cement and groundcement samples; flexure tests on beams, mortar, tiles and any other compression or flexure test performed under displacement […]

Marshall/Indirect tensile digital compression tester

50 kN capacity High precision strain gauge load cell and displacement transducer included Touchscreen graphic diplay 240×128 pixel, icons driven showing figures and diagrams High resolution: 132000 points Large storing capacity on USB pen drive of test data downloadable to PC Ethernet port for connection to PC Language selection Software package available for data processing […]

Marshall compression tester

50 kN maximum capacity, suitable for testing 4″ and 6 ” dia. specimens  High precision load rings fitted with 0.001 mm resolution gauge conforming to standards A bench mounted compression frame with motor and worm gear housed within the base unit. A limit switch is provided for the bottom limit of travel. The machine is […]

Fume exhaust cupboard with aspirator

Certified conforming to EN 14175-2-3, Bureau Veritas Complete with activated charcoal filter for solvents Double aspirator system Complete with stainless steel workbench incorporating sink and bibcocks GENERAL DESCRIPTION The extraction method of the EN 12697-1 and corresponding ASTM standards, often require toxic solvent  (e.g. methylene chloride). This solvent is hazardous to health and is subject […]

Asphalt digital thermometer

GENERAL DESCRIPTION This digital thermometer can be used for various field and laboratory applications in road and concrete testing. Dual range, high resolution, housed in a rugged ABS case. Memory functions: simply press a button and the meter will recall the highest and lowest temperatures measured in the test cycle. Read both °C and °F. […]

Drainage basket

The test is performed for determining binder drainage of bituminous mixtures, for estimating the binder drainage for different binder content and to evaluate the effect of varying the fine aggregate or anti-draining additive content. The test is performed with the Drainage basket and Metal tray. Weights approx.: 75-B0019/A basket 360 g, 75-B0019/B Metal tray 210 […]

Bottle rolling machine

Used for the determination of the affinity between aggregate and bitumen, expressed by visual registration of the degree coverage on uncompacted bitumen-coated mineral aggregate particles after influence of mechanical aggregate particles after influence of mechanical stirring action in the presence of water. Capacity: three bottles 75-B0011/A1 Rotating speed: adjustable up to 80 r.p.m. Accessories 75-B0011/A1   […]

Large size piknometers

Used for determining the theoretical maximum specific gravity of uncompacted bituminous paving mixtures. They can also be used for the calculation of the percent of air voids in compacted bituminous mixtures and the amount of bitumen absorbed by the aggregates. We propose three models: 75-D1122, heavy duty version, 10000 ml cap., specially designed for this […]

Muffle furnace for incineration

GENERAL DESCRIPTION Used to determine the amount of residual mineral matter in the binder extract. Max temperature: 1100°C Power: 3.9 kW Chamber dimension (lxwxh): 210x320x145 mm Outside dimensions: 510x750x660 mm Weight approx.: 89 kg

Solvent recovery unit

Used to recover the solvent liquid after its use for the extraction tests. This unit has been designed to recover non-flammable solvents and consists of two stainless steel chambers, one for dirty solvent and the other for the cleaned solvent. An electric heater in the left-hand chamber distils the solvent, which then passes through a […]

Binder recovery apparatus by Abson method

Used for recovering the asphalt (bitumen) from a solution of a previous extraction. The asphalt is recovered with properties substantially the same as those it possessed in the bituminous mixture and in quantities sufficient for further testing. The apparatus consists of a distillation assembly including: Extraction flasks Glass tubing Inlet aeration tube Electric heating mantle […]

Binder recovery apparatus by vacuum

Used to remove the solvent from the binder/solvent solution in order to determine directly the total content binder in the aggregate/binder mixtures. The apparatus consists of a power operated vacuum pump, fit with vacuum regulator, producing a vacuum down to 200 mbar, a thermostatically controlled water bath, and two flat-bottomed flasks 250 ml capacity with […]

Rotary evaporator for binder recovery

The apparatus is used for the recovery of soluble bitumen from bituminous pavement materials in a form suitable for further testing. During operation, the solution of solvent and asphalt (bitumen) from a prior extraction is distilled by partially immersing the rotating distillation flask of the rotary evaporator apparatus, in a heating oil bath while the […]

Filterless centrifuge binder extractors

High speed with continuous flow Filterless method assures complete filler recovery Automatic ramp and pre-set speed control Up to 100 g or 400 g can be extracted per test Used for rapid filterless separation of filler (ash) from binder solution coming, for instance, from Wire mesh extractor model 75-B0015. The centrifuge can also be used for binder […]

Centrifuge binder extractors

Speed control up to 3600 r.p.m. at 50 or 60 Hz by AC drive (inverter) Electric brake Stable and silent throughout the test Electronic control and digital display CE version available with electromagnetic arrangement to prevent the opening of cover during rotation Explosion proof option Supplied complete with 100 filter discs The centrifuges are used […]

Reflux extractors

Used for the quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. The bitumen content is calculated by difference from the weight of extracted aggregates, moisture content and ash from an aliquot par of the extract. The apparatus consists of a two wire mesh cones with interlocking frames, a cylindrical glass jar and […]

Kumagawa extractor

GENERAL DESCRIPTION Used for the quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. It consists of a balloon, cooling unit, Dean-Stark stopcock, electric heating mantle with regulator and fittings. Two models available: 1 liter and 2 liter capacity. The filtering cartridges are not part of the apparatus and have to be ordered […]

Wire mesh extractor

Used for the quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. The bitumen content is calculated by difference from the weight of extracted aggregates. The filler, or ash, passing through the 63 µm basket has then to be separated from the bitumen/solvent solution using the appropriate centrifuge extractor. See Filterless centrifuge binder extractors, […]

Paper filter extractor

Used for the extraction of binder from hot mixed paving mixtures. It can also be used for determining the moisture content. This model is one of the  versions of the hot extractors accepted by the EN Standards as the Wire mesh extractor, Kumagawa extractor and Reflux extractors. It consists of: Steel pot with gasket and gauze container Dean and […]

Gauge Point fixing jig

Pneumatically operated Accurate alignment of gauge points every time Specially designed to be used for AMPT sample preparation 180 °, 120 ° or 90 ° apart with 70 mm or 100 mm spacing Quickly and easily change between dual, tri or quad arm gluing Optional gauge point setting heads to suit and wide range of […]

Four Point Bend Test for UTM, AST Pro and AsphaltQube

Innovative “floating straight-edge” on specimen transducer displacement measurement eliminates errors Optional fixed point strain measurement referring from outer pivots Designed to subject an asphalt specimen to four point bending with backlash free rotation and horizontal translation of all load and reaction points Sinusoidal or haversine controlled strain or controlled stress loading Controlled force, motorized specimen […]

Trapezoidal Two Point Bend Test for UTM, AST Pro and AsphaltQube

Increases the functionality of Universal Testing Machines, AST Pro and AsphaltQube Engineered from high strength aluminum for high stiffness and light weight performance On-specimen precision LVDT displacement transducer for strain measurements Comes standard with precision +/- 2.5kN load cell for improved clarity and accuracy in your results (only for UTM systems) 25mm and 50mm specimen […]

TSRST and UTSST Test for UTM Machines

Self-aligning couplings for true axial alignment 25 kN capacity Specimen platens 150 mm dia., 50 mm thickness Invar rods provide low thermal contraction for accurate displacement measurement over the full temperature gradient Optional specimen alignment stand Threaded rods to safely support specimen and fixture after fracture  Data Sheet PDF

Uniaxial Fatigue (S-VECD) Test for UTM, AST Pro, AsphaltQube, AMPT Pro and AMPTQube

Increases the functionality of UTM Systems, AMPT Pro, AMPTQube, AST Pro and AsphaltQube Easy to implement on existing equipment Provided with specialized UTS tension test software Optional glue jig assured accurate alignment of top and bottom platens Undexial fatigue tests on asphalt cylinders Test and Dr. Richard Kim’s Simplified Viscoelastic Continuum Damage (S-VECD) test Small […]

Dynamic Modulus Test for UTM, AST Pro, AsphaltQube, AMPT Pro and AMPTQube

Dynamic Modulus E, Flow Time and Flow Number Tests: Input parameter for AASHTO “Mechanistic-Empirical Pavement Design Guide” and property to create master curves for structural design. Values measures over a range of temperatures and frequencies that can be imported into a master curve for characterizing asphalt concrete for pavement design and performance analysis. The value […]

Cyclic and Permanent Deformation Compression Test for UTM Machines

Precision engineered, designed to meet the requirements of a range of testing standards. Easy to set-up and versatile in the use Integrated LVDT holders Constructed using stainless and nitrite hardened steel Data Sheet PDF

Overlay Test for UTM, AST Pro, AsphaltQube, AMPT Pro and AMPTQube

Increases the functionality of UTM systems, AMPT Pro, AMPTQube, AST Pro and AsphaltQube Advanced design for high stiffness and extremely low compliance High precision linear guides to ensure perfect axial loading alignment and no lateral rotation IPC Global’s UTS software allows quick and easy set-up and running of tests Overlay test investigates properties required for […]

Disk-shaped Compaction Tension Test for UTM Machines

Increases the functionality of Universal Testing Machines Precision engineered using zinc plated steel for light weight and anti-corrosion properties Designed for easy, one person set-up Purposely designed for 150 mm disk shaped specimens Easily interchange specimens Data Sheet PDF

Indirect tensile test for UTM, AST Pro, AsphaltQube, AMPT Pro and AMPTQube

The Indirect Tensile Jig and Upgrade Kits are designed to meet the requirements of a range of testing standards and are the perfect accessories to complement your IPC Global Servo-Hydraulic, Servo-Pneumatic Universal Testing System, AsphaltQube or Asphalt Standards Tester.  Precision engineered Easy to set-up and use Integrated LVDT holders Constructed using stainless and nitrite hardened […]

Triaxial test – Universal and Automatic triaxial cell for UTM, AST Pro and AsphaltQube

Universal triaxial cell   Incorporated low friction linear (Thompson) ball bushing on loading shaft to keep fiction to a minimum Limited acrylic (see through) area for greater safety Facilitates 2 LVDTs and mounting brackets for precise direct shaft position measurement Fitted with pressure relief valve for greater safety Facilitates external axial strain transducer mounting system […]

Semi-Circular Bend (SCB Test) for UTM, AST Pro, AsphaltQube, AMPT Pro and AMPTQube

Precision engineered Easily extends the capability of your UTM, AMPT Pro, AMPTQube, AST Pro and AsphaltQube Designed specifically for asphalt specimen sizes of 150 mm diameter Self-aligning top platen for SCB Constructed using high quality materials for long life and test accuracy Constructed using high quality materials AASHTO TP124 Semi-Circular Bend Kit is precision engineered […]

Modular Electro-mechanically operated Asphalt tester AsphaltQube

Brand new technology ihcluding the new revolutionary EmS actuator Easy and versatile with his fully integrated modular system, that includes a 15 kN capacity CEMA1 actuator Enhanced environmental cabinet that grants a wide temperature range with fast and accurate temperature control Easy-to-use and ergonomic testing system Clarity in results with the Integrated Multi Axis Control […]

Modular Servo Hydraulic Asphalt Tester AST Pro

Brand new technology ihcluding the new revolutionary E-Mech Servo-electromechanical actuator Easy and versatile with his fully integrated modular system, that includes a 19 kN capacity hydraulic labyrinth actuator Enhanced environmental cabinet that grants a wide temperature range with fast and accurate temperature control Easy-to-use and ergonomic testing system Clarity in results with the Integrated Multi […]

Environmental chambers for Universal Testing Machines UTM

Closed-loop PID temperature controller Four access port (models for UTM-130), two access ports (model for UTM-30) Stainless steel AISI 304, 18/10 heavy duty construction Triple glazed, argon filled, Lo glass door Defrost system and interior lightning Fan forced ventilation  Ergonomic design provides easy access to chamber Additional features for extended range models only: Programmable digital […]

Servo-Hydraulic Universal Testing Machines UTM, 130 kN cap.

Rigid two column load frame Precision engineered for high stiffness and alignment Double acting high precision actuator High performance servo valve allows sinusoidal loading frequencies up to 70 Hz Motorized crosshead positioning Hydraulic crosshead clamping Fully customizable to suit a large range of testing applications Independent environmental chamber eliminating the transfer to mechanical vibrations to […]

Servo-Hydraulic Universal Testing Machine UTM, 30 kN cap.

Rigid two column load frame Precision engineered for high stiffness and alignment Standard tie-rod sealed actuator Available with double acting, through-rod high precision labyrinth bearing actuator providing superior performance High performance servo valve allows sinusoidal loading frequencies up to 70 Hz Motorized crosshead positioning Hydraulic crosshead clamping Fully customizable to suit a large range of […]

Servo-pneumatic Universal Testing Machine UTM, 16 kN cap.

Robust, high-strenght and compact two column load frame Precision engineered for high stiffness and alignment Digital servo-pneumatic control Optional motorized crosshead available: controlled via the PC, it ensures the crosshead is locked safely without backlashes for waveshape fidelity and high accuracy in tension-compression tests Fully customisable to suit a large range of testing applications 2 […]

Stand-alone Semi Circular Bend SCB tester

Complete stand-alone test system MULTISPEED Compression Testing Machine with digital control and touchscreen display panel Motorized ram for precise and accurate test results Preset testing procedures following most common SCB configurations Auxiliary linear displacement transducer Automatic closed loop control for test speed Rapid approach and return function with soft contact (typically 5N) Programmable pre-loading phase […]

Servo-Pneumatic Four Point Bend Apparatus standalone

Digital servo-controlled pneumatic actuator provides accurate control of loading waveshape Innovative “floating straight-edge” on-specimen transducer eliminates errors due to frame compliance Backlash free rotation and translation on all load and reaction points Sinusoidal or haversine controlled stress loading Controlled force, motorised specimen clamping Non-linear regression data fitting ensures reliable determination of phase and modulus GENERAL […]

Electro-mechanically operated Asphalt Mixture Performance Tester AMPTQube

Brand new technology including the revolutionary EmS actuator Silent and cool Interchangeable transducers and load cells with “plug and play” signal conditioners allowing quick and easy transition of test set-up. Easy-to-use and ergonomic testing system Clarity in results with the Integrated Multi Axis Control System (IMACS) Fully integrated and very compact in design, perfect solution […]

Next generation Asphalt Mixture Performance tester AMPT Pro

Significantly improved ECU performance and innovation Temperatures: 23 degrees Celsius at temperatures below +15 ° C The new Hydraulic Power Supply (HPS) uses inverter technology coupled with a high performance labyrinth bearing actuator to deliver 19 kN of force Easy-to-use and ergonomic testing system Interchangeable transducers and load cells with “plug and play” signal conditioners […]

DWT Universal AASHTO/EN Double Wheel Tracker

Meets and exceed AASHTO and EN standards and many DOT method Fully automatic test performance on two specimens or one specimen Variable wheel speed from 20 to 30 cycles/min Fixed table, mobile wheel 230 mm travel Wheel load of 700/705 N or adjustable from 700 to 1500 N Temperature range from ambient to 80°C (±0.5°C) […]

DWT Hamburg type Double Wheel Tracker

Meets and exceeds AASHTO standards and many DOT methods Fully automatic test performance on two specimens or one specimen Variable wheel speed from 20 to 30 cycles/min Fixed table, mobile wheel 230 mm travel Wheel load of 705 N Temperature range from ambient to 80°C (±0.5°C) Accurate temperature control (±0.5°C) for both in water test […]

DWT Double Wheel Tracker, EN version

Meets and exceeds EN standards  Fully automatic test performance on two specimens or one specimen Variable wheel speed from 20 to 30 cycles/min Fixed table, mobile wheel 230 mm travel Wheel load of 700 N Temperature range from ambient to 80°C (±0.5°C) Accurate temperature control (±0.5°C) for both in water and air test Rut depth […]

Dyna – Track Single Wheel Tracker

Automatic test control by data acquisition and processing system Large permanent memory to store test data and results RS 232 ports for connection to PC and printer Real time display of number of cycles, rut depth and temperatures Tracks for specified number of passes or to specific rut depth Adjustable load cycle frequency Double temperature […]

Internal angle measurement apparatus ILS

Accurate calibration of internal angle of Gyratory compactors and verification of frame stability, to international Standards Quick and accurate measurement of the internal gyratory angle: less than 30 minutes No hot mix required: when, placed into the mould, the device reproduces the internal shearing forces generated by the hot mix during compaction Ideal for periodic […]

Advanced research gyratory compactor Servopac

User defined settings of axial stress, gyratory angle and speed of rotation Measures the shear stress during every gyratory cycle Users can set the desired compaction parameters from either the optional hand-held control pendant or a Windows PC Four column loading frame design provides superior stability Designed for easy specimen insertion, extraction and user safety […]

Fully electro-mechanical gyratory compactor GALILEO Research

High precision, robust load mechanism combined with an extremely rigid frame assures high accuracy and repeatability Load cell fitted directly on the vertical actuator for accurate load measurement and feedback control  User defined axial stress and speed of rotation Sliding transparent door with safety interlock Catch tray to collect expelled liquids using perforated moulds Fresh […]

Fully electro-mechanical gyratory compactor GALILEO

High precision, robust load mechanism combined with an extremely rigid frame assures high accuracy and repeatability Load cell fitted directly on the vertical actuator for accurate load measurement and feedback control Quick and easy manual/mechanical adjustment of the gyratory angle shown on the display  User defined axial stress and speed of rotation Sliding transparent door […]

Gyratory compactor GYROCOMP

High productivity, designed for continuous and heavy use High rigidity thus lightweight due to the propriety orbital system Compact and lightweight, also ideal for mobile laboratories Very reliable and accurate Certified to EN and AASHTO Approved as Superpave™ Gyratory Compactor in U.S.A. Integrated touch-screen control panel with large display Sliding transparent door Full safety and […]

Pavement core drilling machine

6 HP, 4-stroke high quality petrol engine Coring range up to 200 mm dia. Robust, compact and portable Vertical screw feet Complete with strap wrench and spanner Wide range of coring bits with fixed standard coupling available GENERAL DESCRIPTION This simple but rugged machine is a portable unit, which can be easily carried in a […]

Core Drilling Machine, KorBit

Robust design Suitable for up to 150 mm dia. sample coring Three speeds: from 540 to 1850 rpm Complete with protection device conforming to CE prescriptions GENERAL DESCRIPTION Asphalt core drilling machine to take samples from cores up to 150 mm dia. Robust and rigid frame fitted with a 3 selected motor speeds. Complete with […]

Coring machine Multi core-drill

A powerful three speed motor, specifically designed for high performance coring, ensures efficient and high quality specimen preparation Guided rail provides a smooth and precise track for the drill to travel while cutting samples Transparent protection/splash covers conform to CE requirements for safety and ease of cleaning A unique sliding table and stainless sample tray […]

Advanced Automated Asphalt Saw, AUTOSAW II

Touch screen CPU control allows for easy set-up including carriage speed and retraction sequence Intelligent system with adjustable limit switches allow for repetitive cuts with minimal carriage overtravel saving time Protection cabinet with several automatic locking access doors to ensure unparalleled safety and clean operation in laboratory environments. Slab and prism of any shape and […]

Universal asphalt and concrete saw, MULTISAW

Specifically designed to fulfill the stringent requirements of the relevant Standards in terms of precision, planarity and perpendicularity of the specimens. High rigidity and stability Slab and prism of any shape and dimensions can be sawn without additional accessories (see table for maximum dimensions) Jig for round cores, from 100 to 150 mm and for […]

Standard asphalt slab roller compactor

Completely electromechanically operated Conforming to EN 12697-33, 5.2 method and ASTM D8079 8” touchscreen controlled Automatically compacts in displacement controlled mode up to target density/height or up to the (user selectable) load limit Mould dimensions: 500 x 400, 500 x 300, 400 x 300, 300 x 300 and 320 x 260 mm, 195 mm height […]

Advanced asphalt slab roller compactor

Completely electromechanically operated Possibility to program user defined procedures as free combination of load and displacement (or combined) controlled cycles Completely electromechanically operated Conforming to EN 12697-33, 5.2 method and ASTM D8079 21” All-in-one touchscreen PC controlled , PC and software included Includes the compaction procedure defined in the brand new EN 12697-33 method 7.3, […]

Asphalt Prism Shearbox Compactor PReSBOX®

The PReSBOX produces a prismatic speciment with nominal dimensions of 4510 mm (lenght) x 150 mm (width) x 120 to 185 mm (height) Asphalt prisms prepared in the PReSBOX compactor can be sawn or cored to produce 4-6 prismatic beams or 1-4 cylindrical specimens The PReSBOX can be operated by a single person Produces specimens […]

Laboratory digital planetary mixer

New mixing speed control system, granting a much wider range of speed: it is possible to set the right mixing speed to avoid the formation of dust while mixing. Whisk/Planetary speeds adjustable from 12/5 to 149/65 rpm, depending on the mix consistency. Continuously variable speed (VFD technology). Completely new interface with digital alphanumeric display 2×16 characters with […]

Laboratory planetary mixers

Robust table mounted units with planetary mixing action. The bowl and whisk can be easily fit and removed from the mixer. When lifting the transparent cover, a safety switch cuts off the mixer for the operator safety as prescribed by CE. The planetary action ensures a complete and uniform mixing of the materials. For mixing […]

Automatic laboratory mixer BITUMIX

Conforms to EN 12697-35 Ideal to prepare laboratory samples for mix design New improved mixing drum and heating system quickly adjustable up to 250° C Mixing capacity up 30 litres Mixing speed adjustable from 5 to 35 rpm Mixing temperature adjustable up to 250°C Stainless steel (AISI 304) mixing container Temperature control by PT 100 […]

Asphalt binder analyzer by ignition method

Full automatic test cycle with simultaneous display of all test parameters, including weight loss and % High efficiency heating system with additional afterburner for complete combustion of exhaust fumes, conforming to CE prescriptions PID closed loop temperature control Built in weighing system Test time reduced to 30-40 minutes Test performance menu comprising the simultaneous display […]

Hot mix asphalt automatic closed loop extractor PAVELAB50

Fully automatic test cycle: Washing of the asphalt sample (up to 3.5 kg) with solvent and ultrasonic motion, with simultaneous heating and rotation of the drum lined with screening mesh High speed extraction centrifuge for separation of filler from binder solution Condensation of solvent vapour in a stainless steel tank inlcuding cooling coil Automatic recovery […]

Automatic bitumen extractor

Fully automatic testing cycle: Sieving Centrifuge extraction Solvent recovery Conforms to latest anti-pollution requirements Ideal for mastic asphalt Big reduction of toxic fumes in the laboratory High extraction capacity: up to 400 g of filler per test Sensible reduction of extraction time Avoids solvent handling by the operator Low quantity of solvent material used and […]

Adiabatic concrete calorimeter

Real time measurement of heat of hydration of 150mm concrete cube during hardening Reliable evaluation of the heating process inside massive concrete castings Calorimeter cell with minimized heat loss from the concrete sample for true adiabatic conditions Evaluation of the heat of hydration taking into consideration the temperature reached by the concrete GENERAL DESCRIPTION When […]

Unbonded capping pads

This method is used as alternative to the sulphur hot capping of concrete cylinder specimens. The system consist of two alloy steel cap retainers and two 12.5 mm thick neoprene pads which are in contact with the upper and lower concrete surfaces. The pads even out irregularities, distributing the test load uniformly to ensure reliable […]

Specific gravity frame and baskets

GENERAL DESCRIPTION Used with a suitable electronic balance for specific gravity determination of fresh and hardened concrete and aggregates. A purpose built robust frame designed to support the electronic balance. The lower part of the frame incorporates a moving platform, which carries the water container allowing the test specimens to be weighted in both air […]

Determination of restrained expansion of mortar and concrete. Three gang moulds

GENERAL DESCRIPTION Used for determining the restrained expansion of a concrete or mortar containing expansive agent. Made from steel.  Each gang is complete with rods and restrained end plates. 55-C0115/7, 80x80x240 mm, conforming to UNI 8148 Weight approx.: 15 kg 55.C0115/8, 50x50x250 mm, conforming to UNI 8147 Weight approx.: 10 kg Accessories 62-L0035/A Digital length comparator 12.5×0.001 mm, […]

Cylinder capping equipment

GENERAL DESCRIPTION Introduction When testing concrete cylinder specimens it is essential that the two ends are perfectly flat. This range of equipment allows the ends of the various sizes of concrete cylinders or cores to be capped using the sulphur capping compound. Cylinder cappers Used to assure plane end surfaces perpendicular to the axis of […]

Water permeability apparatus

New design that allows space-saving increased and functionality. Determination of the depth of penetration of water under pressure in the cube and prismatic concrete specimens up to 200 mm side and cylinders up to 300 mm height. Graduated burettes already fitted without any addition GENERAL DESCRIPTION Introduction This apparatus is used to determine the depth of […]

Hydraulic shrinkage mould with measurement apparatus

Shrinkage mould The UNI 11307 method is suitable for the determination of hydraulic axial shrinkage on concrete beams during hardening. According to this method, steel pins shall be glued on the head surfaces of the specimen in order to measure the dimensional changes of specimens properly stored in temperature and specified humidity conditions. The test is performed with the 55-C0100/MB11 beam mould […]

Gyratory compactors for cement and concrete

Ideal for mix design of No slump concrete Conforming to NT Build 427 (Scandinavian NORDTEST method) This method, very popular in Scandinavia, is used for mix design and quality control mainly in concrete products plants, where low workable and zero slump concrete is used (for such products as hollow-core slabs, tubes and paving blocks). The […]

Poker vibrators

Wide range of solutions in terms of power supply: electrical, petrol or battery operated Lightweigth instruments, easy to use and carry Ideal for the internal compaction of concrete specimens both in laboratory and in site, and a good alternative to the traditional tamping bar especially when there are large number of specimen to be compacted. […]

Vibrating plate

Light and portable, operated by the car lighter, is ideal for field use. Suitable for vibrating plastic mould up to 150 mm and cylinder moulds up to dia. 160×320 mm. Supplied complete with elastic cord to fit the mould on the vibrating plate. Voltage: 12 V DC for connection to the vehicle cigar lighter or […]

Vibrating tables

Robustly manufactured to operate with minimum noise level. 3000 vibrations per minute (3600 at 60 Hz). Retaining edges to avoid the casual fall of the mould from the table. All models can be completed with clamping device and pedal switch (see accessories) except model 55-C0161/LC, LCZ which include the above items. Model 55-C0161/LC, LCZ is […]

Curing tanks

Zinc plated steel model 55-C0191 Specimen curing tank, 1000 l cap. galvanized steel, complete with metal base specimen supporting grid. It can be fit with various accessories including: immersion analogic and digital heating systems (55-C0191/10, 55-C0191/11) submersible circulator pump to maintain uniform the water temperature (55-C0191/5) metal cover (55-0191/12) Heavy plastic model 55-C0193/A and 55-C0193/R Ideal […]

Programmable accelerated curing tanks

Introduction This test method covers procedures for curing concrete specimens under conditions intended to accelerate the development of strength. Three versions available: 55-C0194/D model which cover the ASTM C684 (Procedure A, warm water method) and BS 1881:112 for 35-55°C hot water method. 55-C0194/DV similar to the above, but covering steam method. 55-C0194/E model, covering both […]

Concrete mortar penetrometers

Model 54-C0143 The 54-C0143 model, which is conforming to ASTM, AASHTO and UNI standards, consists of a spring loaded device which is graduated from 1 to 100 daN, supplied complete with a set of needle pint of 650, 325, 160, 65, 32 and 16 mm2area. A sliding ring indicates the load reached. Supplied complete with […]

Air entrainment meters

Introduction The EN and ASTM standards describe two methods for the determination of air content of compacted fresh concrete: Water column type (eg. Our model 54-C0170/L) and Pressure gauge type (eg. our models 54-C0170/F 7 liters cap. and 54-C0170/D 8 liters cap). The air content  is a very important parameter for the behavior of concrete […]

Concrete mixers

Pan type models 55-C0199/9A, 55-C0199/11, 55-C0199/20 Vertical axle forced mixers Gearbox in oil bath Ease in discharge operation, adjustable in height Separate 4” wheel and drawbar available (as optional for 55-C0199/11 and 55-C0199/20 models only) GENERAL DESCRIPTION Pan type models have been selected  for laboratory use, to prepare concrete specimens and samples. They assure the […]

Verification instruments for moulds and specimens

These instrumentation is used for the assessment of Flatness, Perpendicularity and Strightness of test specimen and mouls as specified by EN 12390-1. They are available, on request, complete with certificate of calibration issued by a competent authority such as NAMAS, ACCREDIA, COfrac etc. The identification labels 55-C0100/D, made from PVC, 100×60 mm in size, are […]

Beam moulds

The proposed models range from the traditional steel models conforming to ASTM standards, to the slitting plastic models, very practical for field use and ideal for production control. Plastic beam moulds A one piece mould manufactured from a robust plastic which is resistant to shock and abrasion. Ideal for field use, the specimen is ejected […]

Cylinder moulds

The proposed models range from the traditional steel models conforming to EN, ASTM and AASHTO standards, to the slitting plastic models, very practical for field use and ideal for production control. Steel models can be supplied, on request, complete with certificate of compliance stating the individual verification with certified instruments. Accessories 55-C0140     Tamping rod 16 […]

Cube moulds

The proposed models range from the traditional cast iron version conforming to EN 12390-1 standards , ideal for laboratory use,  to the plastic models, very practical for field use and ideal for production control. Cast iron models 55-C0100/M10 and 55-C0100/M15, can be supplied, on request, complete with certificate of compliance stating the individual verification with […]

J-Ring apparatus

Used for determining the passing ability (measured by the blocking step), the flow spread and t500 flow time of the self compacting concrete as the concrete flows through the J-Ring. The apparatus consists of a stainless steel crown with 16 bars 18 mm dia. Weight approx.: 10 kg

Sieve segregation test set

Used for determining the sieve segregation resistance of self-compacting concrete. This method is not applicable to concrete containing fibres or lightweight aggregates. The set includes a 300 mm dia. test sieve with perforated plate 5 mm opening,  pan and plastic bucket 11 l cap. Weight approx.: 3 kg

L-Box apparatus

Used for determining the passing ratio of self compacting concrete. The apparatus consists of a L shaped stainless steel frame, supplied complete with filling hopper. Overall dimensions: 700x200x600 mm Weight approx.: 18 kg

V-Funnel apparatus

Used to determine the V-funnel flow time. The test is not suitable when the maximum size of the aggregate exceeds 20 mm. The apparatus consists of a stainless steel V shaped frame fit with a watertight sliding gate and supported by a frame to assure the top funnel horizontal. Overall dimensions: 570x300x920 (h) mm Weight […]

SCC Slump cone

The test is performed for determining the slump flow and t500 time for self-compacting concrete. The test is not suitable when the maximum size of the aggregate exceed 40 mm. The test is performed with the slump cone and steel plate. The SCC slump cone, made from sheet steel protected against corrosion, has a top dia. […]

Unit weight measures

The 54-C0167/1 10 l model, is strictly conforming the BS 1881:Part 107 Standard: 200 mm dia., x 320 mm high, 4 mm thick with machined rim and base internal radius of 20 mm. The other models 54-C0166/2 to 54-C169 have internal dimensions conforming to ASTM C29 and ASTM C138. All made from steel sheet protected against […]

Compacting factor apparatus

The apparatus consists of two conical hoppers having a hinged trap door attached to the lower end of each hopper, allowing the concrete sample to flow freely into the cylindrical mould. The hoppers and the mould are mounted onto a rigid steel frame and are easily removable for cleaning. The complete apparatus is protected against […]

Vebè consistometer

This test method is used to measure the consistency of stiff to extremely dry concrete. Consistency is measured as the time required for a given mass of concrete to be consolidated by vibrating in a cylindrically shaped mould. The small vibrating table operates at a fixed amplitude and frequency . Versions available: 54-C0195 conforming to EN […]

Waltz container

The apparatus consists of a metal box with handles. Dimensions: 200x200x400 (h) mm Weight approx.: 5 kg  54-C0146    Waltz container

K-Slump tester

This device is used to determine the workability and degree of compaction of fresh concrete after being placed in the forms. It can be used for in-situ measurements or inside test moulds and forms. Results can be correlated against the slump test. The operation is very simple: insert the tester  into the concrete up to […]

Concrete workabilimeter

Used to verify the homogeneity of concrete in relation to its workability or plasticity. This test method has particular application for concretes containing chemical admixtures. The apparatus consists of a metal box divided into two parts and fit with an electrical vibrator system. During operation the concrete is poured into  the  first section of the […]

Kelly ball

This method is used to determine the penetration of a hemispherical metal weight into freshly mixed concrete, which is related to the workability of  the concrete. The apparatus consists of a cylinder with one end having a hemispherical shape and the other end fit with a graduated handle. The weight assembly is lowered through a […]

Concrete flow table

The apparatus consists of a double wooden table measuring 700×700 mm hinged at one side. The top table is covered with an inscribed metal plate 2 mm thick: The steel cone, part of the apparatus, has a top dia. of 130 mm  a base dia. of 200 mm and is 200 mm high. Complete with […]

Slump cone test sets

We propose various sets. Versions 54-C0149/B and 54-C0150/C are particularly suitable for site inspectors as are handy, easy transportable and with housing for all parts. All cones are seamless and robust. Cones only and components are also available. See accessories and spares. The slump cone is also known as Abrams cone, from the name of […]

Energy absorption test on slabs

This test is performed to assess the flexural performance and the residual resistance characteristics of fiber reinforced concrete (FRC) and shortcrete slabs. This test has to be performed with a suitable flexural frame as, for instance, our models 50-C1511/FR or 50-C1601/FR, and a control console capable of applying load in displacement control as our model […]

Displacement transducer for measurement of crack opening

This transducer is used for determining the Crack Mouth Opening Displacement (CMOD) conforming to EN 14651. The transducer have to be positioned over the notch sawn previously into the test beam. The specimen has to be loaded by a suitable Flexural frame as, for instance, our models 50-C1511/FR or 50-C1601/FR, and a control console capable […]

Measurement of beam deflection and toughness

This test is performed to assess the flexural performance and the residual resistance characteristics of fiber reinforced concrete (FRC) and shortcrete. This test has to be performed with a suitable flexural frame having proper stiffness and capacity as, for instance, our models 50-C1511/FR or 50-C1601/FR, and a control console capable of applying load in displacement […]

Axial-circumferential compression device

Ideal for axial deformation and diametrical extension measurement. Suitable for dia.150x300mm (6″x12″) and dia.100x200mm (4″x8″) cylinders. Easy and quick application to the specimen. Two different types of measuring systems are available:digital dial gauges or high precision displacement transducers LDT type. NOTE: the model fitted with displacement transducers can be connected to our readout and control units AUTOMAX E MODULUS, […]

Strain gauges

They provide a very accurate electrical signal, strictly proportional to the strain of the specimen submitted to load application, for determining the Elastic Modulus and strength characteristics as alternative to the Compressometer-Extensometers 55-C0222/F. They can be applied to the specimen surface by a special Adhesive-Catalyst agent and other accessories all included in the 82-P0399/C Strain […]

Compressometer-Extensometer for Elastic Modulus determination

Ideal for axial deformation measurement: -MODULUS OF ELASTICITY -UNIAXIAL SECANT ELASTIC MODULUS High sensitivity: 0.02 micron Suitable for various sample size: cylinders up to dia. 160x320mm, cubes up to 200 mm, prisms 40x40x160 mm etc. Easy and quick application to the specimen Can be directly connected to our Automatic control consoles MCC8 and ADVANTEST 9 […]

Universal, open structure flexural frame, 300 kN cap.

  High flexibility universal flexural frame, 300 kN cap. C-shaped open structure for easy specimen loading, Vertical rod hydraulically controlled to compensate frame deformation during the test Load measurement by high precision load cell Large testing space for a wide range of accessories for conventional and tests under control of displacement and strain rate. For connection […]

High stiffness flexural frame, 350 kN cap., DUPLEX

High rigidity (200 kN/mm), especially suitable for testing FRC and sprayed concrete Double testing mode: parallel and orthogonal  For testing different kind of specimens (beams, flagstones, slab) Suitable for testing Round panel dia.800 mm to ASTM C1550 Max span between lower rollers: 1.5m Load measurement by high precision load cell  Piston return by counterweights Piston […]

High stiffness flexural frame, 350 kN cap., SIMPLEX

High rigidity (200 kN/mm), especially suitable for testing FRC and sprayed concrete For testing different kind of specimens (beams, flagstones, slab) having max length 880mm. Suitable for testing Round panel dia.800mm to ASTM C1550 Load measurement by load cell  Piston return by counterweights Piston travel limit switch included GENERAL DESCRIPTION This high stiffness flexural frame […]

High stiffness flexural frame, 200 kN cap., DUPLEX

High rigidity (200 kN/mm), especially suitable for testing FRC and sprayed concrete Double testing mode: parallel and orthogonal  For testing different kind of specimens (beams, flagstones, slab) Max span between lower rollers: 1m Load measurement by load cell or pressure transducer Piston return by counterweights Piston travel limit switch included GENERAL DESCRIPTION This high stiffness […]

High stiffness flexural frame, 200 kN cap., SIMPLEX

High rigidity (200 kN/mm), especially suitable for testing FRC and sprayed concrete For testing different kind of specimens (beams, flagstones, slab) having max length 650mm. Load measurement by load cell or pressure transducer Piston return by counterweights Piston travel limit switch included   GENERAL DESCRIPTION This high stiffness flexural frame has been especially designed for […]

Universal flexural frames 150 kN cap., with adjustable vertical clearance

For testing all standard concrete beams, kerbs, flagstones, pipes etc., using the suitable accessory Large testing space, adjustable vertical clearance Two versions: with pressure transducer and load cell granting high accuracy for testing low strength specimens Connectable to control consoles, Automax and Pilot 4 compression machines Piston travel limit switch included GENERAL DESCRIPTION This versatile […]

Flexural frame for std beams, 100 kN cap.

For testing concrete beams 100x100x400/500 mm and 150x150x600/700 Complete with bearers For center and third point loading Connectable to control consoles, Automax and Pilot compression machines Piston return by counterweights GENERAL DESCRIPTION A simple and practical frame developed for testing on standard concrete beams. The distance of both pair of loading and support rollers can […]

Digital readout unit WIZARD 2

Digital readout unit with wide high-contrast  display 4×20 characters and 6 keys membrane keyboard; real time display of load and stress and applied load rate by symbols for easy adjustment; multi-coefficient calibration allowing Class 1 from 1 % of full scale; can be connected to any make of hydraulic operated testing frame; LAN port for PC […]

Digital readout unit DIGIMAX

  Advanced digital system with touch-screen display unit Compatible with the Data Manager software 82-SW/DM. See accessories Can be connected to any make of hydraulic operated testing frame Recording facility of up to 10 test profiles for each channel allowing quick and easy test start GENERAL DESCRIPTION Introduction Very often may be convenient to update an […]

AUTOMAX E-Modulus console for Elastic Modulus and Poisson ratio determination

E-MODULE software for automatic determination of Modulus of Elasticity and Poisson’s ratio DATAMANAGER software for automatic execution of compression, flexure and indirect tensile tests E MODULE software allows user defined test cycles andautomatic verification of sample centering Test cycle with closed loop digital feedbacks automatically performed by pressing the start button via PC Soft platen-to-specimen contact and smooth load rate control from […]

MCC, multifunctional control console

Completely automatic execution of Compression, Flexure and Indirect tensile tests as well as test cycles to determine the ELASTIC MODULUS MCC Multitest version also suitable for tests under displacement and strain control. Can control up to 2 test frames extendable to 4 with the suitable upgrade Dual control system through PC and keyboard display Multi-language […]

ADVANTEST 9, Servo-hydraulic control console

Performance: user defined test procedures which can be easily performed under load, specific load, displacement and strain control. Flexibility: possibility to connect up to 4 different testing frames from 15 to 5000 kN load capacity, easily selectable by the user friendly software. Accuracy and reliability: long life system due, essentially, to the advanced electronic, efficiency of closed loop […]

Microcore apparatus

Introduction Microcore method is a proven technique for the non destructive evaluation of concrete and masonry strength, taking 28 mm dia. cores and then adequately prepared for the compression test. The cores, due to the small size, does not affect the integrity of the structure thus permitting an easy restoration of the cored surface. This […]

Pullout test apparatus

Used for determining the pullout strength of hardened concrete in test specimens or structures by measuring the force required to pull an embedded metal insert and the attached concrete fragment from a concrete mass. The pullout test apparatus 58-C0178 is used for pre-embedded inserts in fresh concrete mass. It comprises a hydraulic jack 100 kN cap., a […]

Automatic motorized Pull-Off bond strength tester

Ultra-compact and portable equipment ideal for use in and off site Motorized in-built hydraulic actuator High resolution graphic display 128×80 pixels and 5 keys membrane keyboard PID closed-loop control of the load rate Graphic display of actual load, load rate, peak value, strength Battery operated: internal rechargeable LiPo type battery 7.4 V, 2200 mAh. Dial […]

Pull-Off tester

Portable equipment for use in any location High resolution digital display unit Graphic indication of applied load rate Serial port for PC connection Battery operated, complete with AC adapter Indicator of ram position allowing an estimation of the brittle properties of the test sample Supplied complete with traceable calibration certificate GENERAL DESCRIPTION Introduction The apparatus […]

Concrete test hammer

The concrete test hammer is used to evaluate the surface hardness of hardened concrete in order to evaluate the strength in various parts of the structure   Main features: Impact energy: 2.207 Nm Measurement range: 10 to 70 N/mm2 Aluminium case, complete with carrrying case, grinding stone and instruction manual Case dimension: 190x100x350 mm Weight […]

Digital rebound test hammer

Test procedure conforming to EN 12504-2 and ASTM C805  Measuring range: from 10 to 130 N/mm2 Allows to generate customized test procedure Storage capacity 2 Mb         Saves, displays and downloads data to PC via USB port PC software included                     Integrated rechargeable lithium ion battery of 1600 mAh and multi-voltage / multi-frequency battery charger Measurement and indication […]

Deflectometers

Used for determining the deflection of bridges, ceilings or any suspended structure. Comprising: swing arm with clamp for total orientation in any position q.ty 3; wire coil 20 m q.ty 3; dial gauges 30×0.01 mm q.ty 3; plumb weight q.ty 3; carrying case. Weight approx.: 3 kg Accessories 58-C0224/1   20 m low thermal deformation steel […]

Flat Jacks

Introduction The in-situ stress, deformability and resistance feature of masonry can be determined by the flat jack method . The test is performed by making a cut to a uniform depth into the mortar courses and inserting the flat jack or couple of jacks, which are pressurized to the desired level. Test modes: For stress determination a […]

Crack width microscope

GENERAL DESCRIPTION A high quality microscope designed for measuring crack widths in concrete members, masonry walls and other structures. The apparatus operates by an adjustable lamp unit and the image is focused by turning a knob. The eyepiece scale can be turned through 360° to align with the direction of the crack or pitch under […]

Crack width gauges

Internal or external use Monitors the opening or closing of crack to an accuracy of 1 mm Crack record cards supplied with each gauge simplifies monitoring Capable of monitoring vertical as well as horizontal movement GENERAL DESCRIPTION Made from plastic. Used for measuring the crack widths in different positions: walls, corners, floors and difference of […]

Mechanical strain gauges

Digital gauge 0.001 mm resolution Serial output for PC connection (with 82-D1261/LINK) GENERAL DESCRIPTION This apparatus used for determining the length changes  was originally designed for use on concrete structures, but can also be conveniently used for any other type of structure including steel. The test set includes the extensometer with digital gauge resolution 0.001 […]

Digital deflection measuring system for suspended structures

Modular system: basic configuration with 3 measuring units Expandible up to 6 units DATALOG 8, 8 channels datalogger, in-built battery operated with rigid carrying case suitable for use on field. 5.7” touch screen colour graphic display Displacement transducers with 50 mm travel and 12 m cable allowing increase manageable on site Modular system: basic configuration with 3 measuring […]

Cross-Hole Analyzer for foundation piles Wireless modular version

Integrated wireless system with 2 motorized reels; expansion options for 1 – 2 channels; with multi-reels system (up to 4) the tomographic investigation is performed providing complete information on pile quality and homogeneity over its whole length; the system is completely managed via a rugged Android tablet (included); easily transportable with the very small wheeled […]

Ultrasonic pulse analyzer

Digital scope, 2 MHz sampling rate, 12 bit resolution Advanced picking algorithm providing the real arriving time of the pulse Signal processing by FFT method (Fast Fourier Transform) Assessment of concrete strength with combined method Ultrsonic velocity/Rebound index (SonReb) 7 selectable pre-amplifier gains (impulse amplitude) Transmitter pulse 2500 V Transit time up to 16 ms […]

Ultrasonic pulse velocity tester

For the non destructive evaluation of concrete homogeneity and determination of Dynamic Elastic Modulus Ergonomic and compact Lightweight and portable Battery operated Large size digital display 128×64 pixel Digital calibration High price/quality ratio GENERAL DESCRIPTION Introduction The 58-E4800 UPV tester is used for quality control and inspection of concrete. It measures the transit time of […]

Surveymaster SM. Protimeter

The Surveymaster is the industry standard moisture meter for surveying and investigation moisture in buildings. Two operation modes: search and measure, helping the user to distinguish sub-surface from surface moisture, essential information when trying to establish the extent and cause of a dampness problem. The actual moisture content of wood is shown on the digital […]

Resonance frequency meter

LCD 7″ Touch screen integrated monitor Integrated PC card Software utility for positioning of measuring and impact points Automatic measurement of resonance frequencies values Display of harmonic frequencies Storage of data on USB memory RES – Lab software included Used for determining the Longitudinal, Transverse (Flexural) and Torsional resonant frequency of concrete and natural stone […]

Air and Water permeability test set. John Figg method

This method covers the determination of susceptibility to chloride and carbonation penetration into the concrete. The apparatus can be used for: Internal (deep permeability) test A hole 10 mm dia., 40 mm deep is drilled and plugged leaving a cylindrical test void 10 mm dia. 20 mmhigh, situated 20 mm below the concrete surface. The […]

Water penetration – Dr Carstens method

For the determination of water permeability of building materials and prefabricated building parts. The test can be performed either horizontally or vertically. The test set consists of 3 vertical and 3 horizontal, water penetration test tubes, 250 ml washing bottle and 250 g of plasticine cement. Case dimension: 420x280x90 mm Weight approx.: 1.75 kg Spare […]

Oxigen permeameter. Cembureau method

This method, which is applicable to cast and cored concrete specimens, concerns the determination of the concrete permeability to oxygen conforming to the Hagen-Poiseuille relationship. The apparatus consists of: Permeability cell for specimens 150 mm dia, 50 mm high Volumetric gas flow meter, soap bubble type High precision pressure regulator Digital readout unit and pressure […]

Carbonation test set

This simple test allows the measurement of depth of carbonation through the surface of concrete. During the test, the broken or cored surface is sprayed with phenolphthalein solution to detect the loss of alkalinity associated with carbonation. Test set is conforming to EN 13295 for measurement of the depth of carbonation and including: – 1 plastic […]

Deep scanning metal locator

Scans through solid concrete Pinpoints the location and depth of target Differentiates between steel rebar and copper pipe Eliminates guesswork, needless holes, broken drills and saw blades Essential tool for concrete contractors, remodelers, plumbers and electricians GENERAL DESCRIPTION Finds rebar and metallic pipes, conduit, metal studs, junction boxes and metal framing up to 150 mm […]

Covermeter, Bartracker

Rebar location Rebar orientation Depth of cover Cover reading thickness mm or inches Large graphic display with backlight Multiple language menu structure Signal strength bar Interchangeable heads with led and keypad User selectable bar range sizes and numbers Autosize mode for quick bar diameter determination Orthogonal mode for bar diameter determination Other models of search […]

Cor Map apparatus for rebar corrosion location

A simple economical method for identifying areas of probable rebar corrosion in (for example) Bridge decks Parking garages Concrete piers and docks Substructure Tunnel lining Foundations   GENERAL DESCRIPTION Corrosion, which is an electrochemical process, occurs in concrete when oxygen and moisture are present. The measurements made with the Cor Map apparatus, using the half […]

Chloride ion penetration meter

Double version: model with 4 or 8 independent channels  Wide touch screen color display Programmable test duration and adjustable measuring rate starting from 1 minute Unlimited data storage on SD card   GENERAL DESCRIPTION The concrete durability is negatively influenced by the chloride ion penetration. This test method allows evaluation of chloride permeability characteristics of concrete. […]

Portable core drilling machine

Light and portable: weighs 36 kg only Steel tilting column up to 60-75° Slide with rollers and ball bearings Aluminium base fixable by anchors or vacuum horizontally or vertically ‘ GENERAL DESCRIPTION The machine is composed by three main parts: Electric motor speed reducer Light alloy base with adjustable feet, and wheels Support column These […]

Universal core drilling machine

Full 360° operation for coring at any angle Main column extendable in height up to 3850 mm Robust and stable unit Rack feed (drilling excursion) 1000 mm long 3 working speeds GENERAL DESCRIPTION This robust versatile machine is ideal for field where it is necessary to core at any angle. The extension columns (see accessories) […]

Specimen grinding machine

easy and precise grinding of concrete specimens, natural stones, block pavers, ceramic materials etc. high productivity with large base table for simultaneous grinding up to two concrete cubes 100 and 150 mm or two cylinders dia. 150 and 160 mm or up to 4 rock cores ergonomic compact bench model to safe laboratory space improved […]

Specimen grinding machine

To grind concrete specimens, natural stones, tiles, block pavers, ceramic materials etc. Large base table for grinding contemporaneously up to three 100 mm cubes, or three 150 mm cubes, or two 200 mm cubes and concrete/tile blocks of various sizes (see drawing of working area). For cylinders up to dia. 160×320 mm Motorized radial displacement […]

Universal asphalt and concrete saw, MULTISAW

Specifically designed to fulfill the stringent requirements of the relevant Standards in terms of precision, planarity and perpendicularity of the specimens. High rigidity and stability Slab and prism of any shape and dimensions can be sawn without additional accessories (see table for maximum dimensions) Jig for round cores, from 100 to 150 mm and for […]

Concrete, asphalt, rock and masony saw

This universal saw, completed with the suitable accessory, can be used to cut concrete, asphalt and rock cores, and irregular rock samples in order to obtain geometrically defined samples. It can be fit with 300 to 450 mm dia. blades. The head is adjustable in height. The tilting motor head permit cuts up to 45° […]

Automax SMART line, fully automatic tester

PC control option When connected to PC, the system is fully computerized and controlled by the Data Manager software Accurate load rate control for quality testing An accurate and constant load rate application without large fluctuations (typically 10% of the pre-set value) not only guarantees testing to Standards and reliability of results, but also allows […]

Pilot SMART line, entry level automatic tester

Accurate load rate control for quality testing An accurate and constant load rate application without large fluctuations (typically 10% of the pre-set value) not only guarantees testing to Standards and reliability of results, but also allows the test to be performed by operators who do not have experience. The advantage of the test automation. The […]

Digimax SMART line, semi automatic digital tester

Accurate load rate application High test throughput: up to 40 compression tests per hour Advanced digital system with touch-screen display unit Connectable to a second frame (as optional) Compatible with the Data Manager software 82-SW/DM (new release compatible with SMART Line units) Can be connected to any make of hydraulic operated testing frame Recording facility […]

Compression and flexure machines retrofit

In many cases it may happen that the customer has already an old compression or flexural machine, with old pressure gauge and not more reliable readout unit. In these cases, rather than buying a new machine, it is enough to update the hydraulic system and the readout unit. The control unit and the pump group fitted […]

Load cells

High accuracy: Class 1 EN ISO 376 Stainless steel construction Can be supplied with Official or Traceable calibration certificate.   GENERAL DESCRIPTION These high performance cells have been specially designed to meet the stringent requirement of EN ISO and ASTM standards, for calibration of compression testing machines. The cells have to be connected to a […]

Digital instrumentation

High resolution: 256,000 points ( less than 0.05% of full scale) Large graphic display: 240×128 pixel Language selection: English, French, Spanish, German and Italian Large permanent memory: up to 960 readings Two RS 232 serial ports for PC and printer Remote control MS EXCEL Template available for producing calibration certificates conforming to EN/ASTM   standards […]

Strain gauged column and tester for load transfer verification

One cell only, 3000 kN cap., to test either the force accuracy and force transfer Digital tester also connectable to other cells Tester and column can be supplied with official calibration certificate issued by a European   accreditation laboratory Suitable for calibration of Class 1 compression testers GENERAL DESCRIPTION Introduction The verification of force transfer […]

Distance pieces to adjust the vertical daylight

Made of steel. Used to reduce the vertical daylight of the compression machine depending on the size of the specimen and considering that, in general, the maximum piston travel is 50 mm. The following sketch and table are a suitable application guide to help you in the selection of required distance pieces.    

Data manager PC software

Two different DATAMANAGER software are available: 50-C7022/SOF is compatible with MCC and ADVANTEST control consoles and suitable for remote control of the system, data acquisition, processing and filing. It’s included in the supply of the machine. 82-SW/DM is new intuive and smart DATAMANAGER software, very easy to use, complete with many functions, totally flexible and […]

Flexural test device for concrete beams

Double upper bearer for third point test and center. Total height: 370 mm when adjusted for 150 mm beams and 320 mm for 100 mm beams. The 370 mm vertical daylight can easily obtained removing the lower platen of the compression tester. Max vertical daylight: 160mm (total height:370mm) Min vertical daylight: 110mm (total height:320mm) Max […]

Compression devices for cement and mortars

Robust frame fitted with an upper platen with spherical seat that moves vertically sustained by a spring. The apparatus can be placed and centered directly on the lower machine platen. The 50-C9030 and 50-C9032/H, conforming to EN 196 are designed to test portions of 40x40x160 prisms broken in flexure, while the 50-C9032, conforming to ASTM […]

General utility compression frames

General utility standalone frames for testing cubes and cylinders 50-C13Z00, 50-C23Z00 and 50-C34Z00, 1500kN, 2000kN and 3000kN cap, frames consist of a rigid welded steel structure, with spherical seat and platens suitable for testing cylinders and cubes (see TECHNICAL SPECIFICATIONS table). Supplied complete with pressure transducer, flexible plastic fragment guards and connection kit for separate control console. Pedestal […]

EN 12390-4, EN 772-1 Compression frames

EN  12390-4 Testing frames for cubes and cylinders  50-C46Z00, 50-C56Z00 and 50-C78Z00 frames, 2000 to 5000 kN cap., feature a four column rigid welded steel construction, with heavy duty spherical seat in oil bath, tested for stability conforming to EN 12390-4. Complete with pedestal, front door and rear transparent fragment guard (except for the 4000 […]

ASTM C39, C140, AASHTO T22 Compression frames

ASTM-AASHTO standalone frames for testing cylinders 50-A12Z00, 50-A22Z00 and 50-A32Z00, 1500kN (335 klbf), 2000kN (450 klbf) and 3000kN (660klbf) cap, frames consist of a rigid welded steel structure, with spherical seat and platens 165 mm dia., suitable for testing cylinders from dia. 4”x8” to 6”x12” as prescribed by ASTM C39 standard. The vertical clearance allows […]

Automatic compression testers for cubes, cylinders and blocks PILOT

Rigid welded steel construction Spherical seat allows free alignment at the initial contact with the specimen Automatic control of test execution conforming to Standards Dual user interface display and PC Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale (from 1% on request) Compatible with the new intuitive easy to […]

Semi-Automatic compression testers for cubes, cylinders and blocks WIZARD 2

Rigid welded steel construction Accuracy Class 1 (EN) starting from 10% of full scale (from 1% on request) 2 channels for load sensors with 65000 div. resolution (better than 0.01% of full scale) Unlimited store capacity on USB pen drive of test data downloadable to PC via LAN port Digital readout unit with wide high-contrast […]

Automatic compression testers for cubes and cylinders PILOT

Rigid welded steel construction Spherical seat allows free alignment at the initial contact with the specimen Automatic control of test execution conforming to Standards Dual user interface display and PC Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale (from 1% on request) Compatible with the new intuitive easy to […]

Semi-Automatic compression testers for cubes and cylinders WIZARD 2

Rigid welded steel construction Accuracy Class 1 (EN) starting from 10% of full scale (from 1% on request) 2 channels for load sensors with 65000 div. resolution (better than 0.01% of full scale) Unlimited store capacity on USB pen drive of test data downloadable to PC via LAN port Digital readout unit with wide high-contrast […]

Automatic compression testers for cylinders and blocks, 3000 kN (660 klbf) cap. PILOT

Four column, rigid welded steel construction Premium Heavy Duty spherical seat and rectangular platens 310x410x90 mm (12.2”x16.1”x3.5”) for testing blocks according to ASTM C140 and ASTM C1314 Upper platen and spherical seat are mounted on an axial screw assembly allowing easy adjustment of vertical clearance using slotted distance pieces. Innovative upgrading kit for easily switch […]

Super-Automatic compression testers for cylinders AUTOMAX

Rigid welded steel construction ASTM spherical seat allows free alignment at the initial contact with the specimen Automatic performance of the complete test cycle with closed-loop digital feedback Fully computerized system Dual user interface display and PC Accuracy Class A (ASTM) starting from 10% of full scale (from 1% on request) Compatible with the new […]

Automatic compression testers for cylinders PILOT

Rigid welded steel construction ASTM spherical seat allows free alignment at the initial contact with the specimen Automatic control of test execution conforming to Standards Dual user interface display and PC Accuracy Class A (ASTM) starting from 10% of full scale (from 1% on request) Compatible with the new intuitive easy to use DATA MANAGER […]

Semi-Automatic compression testers for cylinders WIZARD 2

MAIN FEATURES Compression device to test 50mm (2″) cubes (50-C9032/H) 12345678910 Rigid welded steel construction ASTM spherical seat fully complaint to ASTM C39 for testing 4” x 8” and 6” x 12” cylinders Accuracy Class A (ASTM) starting from 10% of full scale (from 1% on request) 2 channels for load sensors with 65000 div. […]

Super-Automatic compression testers for cubes, cylinders and blocks AUTOMAX

MAIN FEATURES Splitting tensile test device for cylinders (50-C9000/B) 123456789 Four column high stiffness welded frame tested for stability Heavy duty spherical seat in lubricating oil bath Automatic control of test execution conforming to Standards Automatic performance of the complete test cycle with closed-loop digital feedback Automatic loading and loading by electronic valves Fully computerized […]

Automatic compression testers for cubes and cylinders and blocks PILOT

MAIN FEATURES Compression machine 50-C47C02 with 50-C10C/3F three way valve, 50-C92Z10 500 kN compression frame and accessories 12345678910 Four column high stiffness welded frame tested for stability Heavy duty spherical seat in lubricating oil bath Automatic control of test execution conforming to Standards Dual user interface display and PC Accuracy Class 1 (EN) and Class […]

Super-Automatic compression testers for cubes and cylinders AUTOMAX

MAIN FEATURES Splitting tensile test device for cylinders (50-C9000/B) 123456789 Four column high stiffness welded frame tested for stability Heavy duty spherical seat in lubricating oil bath • Automatic control of test execution conforming to Standards Automatic performance of the complete test cycle with closed-loop digital feedback Fully computerized system Dual user interface display and […]

Automatic Compression Testers for Cubes and Cylinders PILOT

MAIN FEATURES Compression machine 50-C46C05 with 50-C10C/3F three way valve, 50-C1201/BFR flexural frame, 50-92Z10, 500 kN compression frame and accessories 12345678910 Four column high stiffness welded frame tested for stability Heavy duty spherical seat in lubricating oil bath Automatic control of test execution conforming to Standards Dual user interface display and PC Accuracy Class 1 […]

Semi-Automatic EN testers for cubes, cylinders and blocks DIGIMAX

MAIN FEATURES 12345 Dual user interface display and PC Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale. On request from 1% with special calibration procedure. See upgrading options. Compatible with the new, intuitive and smart DATA MANAGER Software. Very easy to use, complete with many functions, totally flexible, open to network […]

Semi-Automatic EN testers for cubes, cylinders and blocks WIZARD 2

Home Products Concrete Semi-Automatic EN testers for cubes, cylinders and blocks WIZARD 2 Semi-Automatic EN testers for cubes, cylinders and blocks WIZARD 2 REQUEST MORE INFO print page EN 12390-4 MAIN FEATURES 3000kN compression machine for cube and cylinders, WiZARD, model 50-C56A02 12 Accuracy Class 1 (EN) starting from 10% of full scale (from 1% […]

Hydrometer, Soil Test, ASTM 151H, .995 to 1.038°

Potassium Ion Test Kit (Test Strip Method)

The OFITE Potassium (K+) test is suitable as a rapid guiding test for potassium in water, drilling fluids, and extracts from soil samples. A particular advantage of the test is that potassium can be semi-quantitatively determined in the presence of 10 times its amount of sodium. The test strips have a color scale graduated as […]

Recording Calcimeter with Data Acquisition

Introduction The Calcimeter is used to determine the amount of Calcium Carbonate (CaCO3) and Magnesium Carbonate (Dolomite) in a sample of alkaline earth carbonates such as oil well cores or drilled cuttings. Calcite buildup in drilling fluids and in water treatment processes causes scaling problems. Data from the Recording Calcimeter can help determine the proper […]

SRS-150 Residual Ring Shear Testing System for Soils

This system features electro-hydraulic closed-loop digital servo control of the shear and normal loads for test automation. Loads or deformations for both the shear and normal actuators can be prescribed for automatically performing conventional ring shear tests as well as more advanced tests. This system can be easily programmed to perform tests such as the […]